User manual GEMINI CDX-04

[. . . ] POWER-CORD PROTECTION: Power-supply cords should be routed so that they are not likely to be walked on or pinched by items placed upon or against them, paying particular attention to cords at plugs, convenience receptacles, and the point where they exit from the product. OUTDOOR ANTENNA GROUNDING: If an outside antenna or cable system is connected to the product, be sure the antenna or cable system is grounded so as to provide some protection against voltage surges and built-up static charges. Article 810 of the National Electrical Code, ANSI/NFPA 70, provides information with regard to proper grounding of the mast and supporting structure, grounding of the lead-in wire to an antenna discharge unit, size of grounding conductors, location of antenna-discharge unit, connection to grounding electrodes, and requirements for the grounding electrode. LIGHTNING: For added protection for this product during a lightning storm, or when it is left unattended and unused for long periods of time, unplug it from the wall outlet and disconnect the antenna or cable system. [. . . ] The unit will turn on and the LCD DISPLAY(10) will light up. Pushing POWER(6) a second time turns the unit off. DISC TRAY: The DISC TRAY(7) is where the CD is held during loading, unloading, and playback. The DISC TRAY(7) holds both 12 cm and 8 cm CDs and automatically closes after remaining open for three minutes. OPEN/CLOSE : Pressing OPEN/CLOSE(8) opens or closes the DISC TRAYS(7) for loading and unloading CDs while the CDX-04 is not playing. After loading another CD you may press the STOP/EJECT(9) button to close the tray. nOTE: DISC TRAY WILL NOT OPEN WHILE THE CDX-04 IS IN PLAY MODE. DISPLAY: The LCD DISPLAY(10) shows total tracks, track number, pitch value, single-auto cue, continue (continuous play), three different time displays, track time elapsed, track time remaining and total time remaining on disc. time is measured in minutes , seconds , and frames. PLAYBACK DISPLAY BAR: The PLAYBACK DISPLAY BAR(11) displays the play time elapsed and remaining for each track. The display flashes slowly when the track has 30 seconds remaining and pulses rapidly when play time is down to 15 seconds. To enable the stutter mode enter PAUSE mode and use the JOG SEARCH WHEEL(17) to select a CUE(13) position. Push the PLAY/PAUSE(12) button again to initiate a CUE(13) point, the BLUE CUE LED(13) will turn on when a CUE(13) is selected CUE: With the unit in the PLAY mode and after a CUE POINT(13) has been programmed, pressing CUE (13) will cause the CD player to enter the PAUSE mode at the CUE POINT(13). Holding down the CUE (13) button activates PREVIEW mode and starts playback from the CUE POINT(13). releasing the CUE(13) button will return the CUE(13) to the preset CUE POINT. The CUE(13) will stay in memory until a new CUE POINT is selected or the CD is ejected from the unit. The BLUE LED(13) will flash while selecting a new CUE POINT after the first one has been made. BOP: Once your selected track has a CUE point, press BOP(14) in order to begin the track in PLAY mode. Press the BOP(14) again and the track will instantly begin again at the selected CUE point. Do not use this CD player at temperatures below 41°F/5°C or higher than 95°F/35°C. The apparatus should not be exposed to dripping or splashing, and no objects filled with liquids such as vases should be placed on the apparatus. Place the unit in a clean and dry location. [. . . ] CUE POINTS for SEAMLESS LOOPS can be selected on the FLY, with any of the LOOP-IN(20) buttons. Press LOOP-OUT(21) again to exit the SEAMLESS LOOP, CUE-B will remain solid. Use RE-LOOP(22) to reactivate a SEAMLESS LOOP during playback or start playback from the LOOP-IN(20) CUE POINT just like the BOP(14) feature when a SEAMLESS LOOP is not in memory. Use ROBO START(26) in SINGLE-AUTO CUE MODE(18) to alternate play between the CDX-04's two CD players (one track from one side, then one from the other). [. . . ]