User manual GEMINI CFX-50

[. . . ] POWER-CORD PROTECTION: Power-supply cords should be routed so that they are not likely to be walked on or pinched by items placed upon or against them, paying particular attention to cords at plugs, convenience receptacles, and the point where they exit from the product. OUTDOOR ANTENNA GROUNDING: If an outside antenna or cable system is connected to the product, be sure the antenna or cable system is grounded so as to provide some protection against voltage surges and built-up static charges. Article 810 of the National Electrical Code, ANSI/NFPA 70, provides information with regard to proper grounding of the mast and supporting structure, grounding of the lead-in wire to an antenna discharge unit, size of grounding conductors, location of antenna-discharge unit, connection to grounding electrodes, and requirements for the grounding electrode. LIGHTNING: For added protection for this product during a lightning storm, or when it is left unattended and unused for long periods of time, unplug it from the wall outlet and disconnect the antenna or cable system. [. . . ] please refer servicing to a qualified technician. Do not use chemical solvents to clean the unit. Keep the laser pickup clean by keeping the drawer closed. Keep this manual in a safe place for future reference. DIMMER: Turn the DIMMER (9) to the right to increase brightness of the DISPLAY (10), and push it in to lock the setting. DISPLAY: The DISPLAY (10) shows the track number, pitch value, singleauto cue, continue (for continuous play), and 3 different time displays. These time displays are time elapsed on the track, time remaining on the disc and time remaining on the track. The display flashes slowly when the track has 15 seconds remaining and pulses rapidly when playing time is down to 5 seconds. PLAY/PAUSE : Each press of the PLAY/PAUSE BUTTON (12) causes the operation to change from play to pause or from pause back to play. CUE/PREVIEW: With the unit in the PLAY mode and after the CUE POINT has been programmed, pressing CUE/PREVIEW (13) will cause the CD player to enter the PAUSE mode at the programmed CUE POINT. Holding down the CUE/PREVIEW (13) button changes the function to PREVIEW and starts the CD from the programmed CUE POINT. releasing the CUE/ PREVIEW (13) button will return the CD laser to the preset CUE POINT. TRACK : The TRACK (14) buttons let you select the track to play. Since the CFX-50 is a dual CD player, most of the functions and controls are duplicated on both sides of the CD player. To eliminate confusion and to make the drawings easier to understand, we will only number the left side functions and controls. To set the proper voltage, follow these steps: 1. Place the head of a screwdriver in the center of the VOLTAGE SELECTOR SWITCH (1) found on the rear panel. SEARCH : The SEARCH (15) buttons are used to move forward or reverse while in play or pause mode. see the CUE INSTRUCTIONS section for more information. TIME: The TIME BUTTON (16) switches the time display between the three available choices listed under DISPLAY (10). sINGLE: Pressing the SINGLE (17) activates the AUTO CUE FUNCTION. B-EDIT: After a LOOP has been memorized you can change the length of the LOOP by pressing B-EDIT (21) then use the JOG WHEEL (24) to adjust the length. [. . . ] Move the JOG WHEEL (24) to the precise spot you want play to begin and push the PLAY/PAUSE (12) button to memorize the CUE POINT. press the CUE BUTTON (13) to return to the memorized CUE POINT. Push the PLAY/PAUSE BUTTON (12), and the unit will instantly play from the spot selected. To fine tune a CUE POINT, pause play at the memorized CUE POINT (the CUE/PREVIEW (13) LED will glow and the PLAY/PAUSE (12) LED will blink), then use the JOG WHEEL (24) to scan frame by frame (1/75th of a second) to where you want play to begin (the CUE LED will blink while you scan). [. . . ]