User manual GEMSTAR GM-190B

[. . . ] Connect the monitor into an outlet on a circuit different from that to which the receiver is connected. Consult your local dealer or a qualified technician. FCC Warning: To assure a continued FCC compliance, a user must use a grounded power supply cord and the provided shielded video interface cable with bonded ferrite cores. Also, any unauthorized changes or modifications to this monitor will void the user s authority to operate this device. [. . . ] Keep the monitor away from magnetic objects, motors, TV sets, and transformers. Do not place heavy objects on the cable or power cord. For PLUG CABLE EQUIPMENT, the socket outlet should be installed near the equipment and should be easily accessible. 2 Care and Maintenance Care Avoid exposing your monitor directly to sunlight or other heat sources. Place your monitor away from the sun to reduce glare. Put your monitor in a well-ventilated area. Do not place anything heavy on top of your monitor. Make certain that your monitor is installed in a clean and moisture-free area. Keep your monitor away from magnets, motors, transformers, speakers, and TV sets. Safety Tips If smoke, an abnormal noise or an odor comes out of your monitor, switch off the power immediately and call our service center. Never remove the rear cover of your monitor cabinet. The display unit inside contains high-voltage parts and may cause an electric shock. Never try to repair the monitor yourself. Always call your service center or a qualified technician to fix it. Note: This user s manual contains graphics and information that is for reference purposes only and is subject to change without notice. 3 CHAPTER 1 INTRODUCTION BEFORE INSTALLING YOUR MONITOR Read this manual cover to cover. PAY ATTENTION to all WARNING and CAUTIONS DO NOT use computer components not recommend by the manufacture. Do not attempt to service the monitor your self. If a problem occurs, contact the manufacture's authorized service center. ABOUT YOUR MONITOR This monitor is a microprocessor-controlled, color monitor that uses a TFT LCD panel. The monitor conforms to EPA Energy Star and VESA DPMS (Display Power Management Signaling) power management standards. Our monitors also provide one option to accept the video input (like NTSC or PAL signal), you can switch these input signal through OSD and the video OSD setting please refer to the Chapter 3. RGB AND DVI MODE This monitor is equipped with a microprocessor that identifies your computer's video mode and allows user to adjust the settings. I can support the traditional analogue signal or the new DVI-D signal. 4 FACTORY-PRESET MODES Table 1 shows standard video mode setting that have been pre-adjusted at the factory for accurate video display. These setting are stored in the monitor's memory Table 1. Factory-Preset Modes Mode NEC VGA Resolution 640x400 640x350 720x400 640x480 640x480 640x480 800x600 800x600 800x600 800x600 1024x768 1024x768 1024x768 1280x1024 1280x1024 640x480 832x624 1024x768 1024x768 H-Freq. (KHz) 24. 83 31. 47 31. 47 31. 47 37. 86 37. 5 35. 16 37. 88 48. 08 46. 87 48. 36 56. 47 60 63. 98 80 35 49. 7 48. 78 60. 241 V-Freq(Hz) 56. 4 70 70 60 72 75 56. 3 60. 3 72. 2 75 60 70 75 60 75 66. 7 74. 55 60 74. 927 SVGA XGA SXGA Macintosh 5 SPECIFICATIONS 19 LCD Monitor Overall Dimension (HxWxD): Shipping Weight Gross/Net Weight: Effective Display area (H/V): Display colors: Scan Frequencies: Horizontal Vertical Number of Pixels: Pixel pitch: Picture Tube: Power: Input Consumption Video Connector: Audio connector (optional) Speaker (optional) RGB Signals: Video Sync DVI Signal Display Data Channel: Compatibility 426 x 444 x 215 mm 13Kg/14Kg 376. 32 x 301. 56 mm 16. 7M colors 31. 47K to 80KHz 60Hz to 75Hz 1280x1024 pixels 0. 294x0. 294 mm 19" TFT LCD panel 110-240VAC(auto-sensing) Frequency: 48-62Hz 45Watts maximum (on) 3 Watts (Power saving off mode) 15pin Mini D-sub (Standard) 1 x stereo input 2Watts x 2 Analog RGB 0. 7Vp-p/75 Separate TMDS VESA DDC 1/2B 6 Operations: User Controls On Screen Display Adjustment Control Type: Compatibility: Environmental Limits: Operating Temp Storage Temp. [. . . ] Menu Press the Menu key to activate the on screen display screen. Press twice to turn off the on screen display screen. After 30 sec idle time, the OSD screen will automatically turn off. Auto adjustment Pressing this key to get the better visual performance. 12 CHAPTER 3 ADJUSTING THE MONITOR The LCD monitor is designed to work with a range of compatible video adapters on the market. [. . . ]