User manual GENIUS DSC13M SMART

[. . . ] We expect it will give you all the things you hoped for. But before you begin using it, please read through this manual carefully and follow the instructions to avoid any possible damages caused by improper usage. Proper Care This product consists of intricate electrical parts. To use it properly, do not drop or hit the camera when taking pictures. Avoid using or placing the camera in the following locations: 1. Sealed vehicles or places exposed to direct sunlight or places subject to extremely high temperatures or heat. 3. [. . . ] NoteIf the DSC-1. 3M Smart Setup screen does not display automatically, 1. Go to the Taskbar and click start, then Run. 2. Type D:\SETUP. EXE, WHERE D: is the designation of your CD-ROM drive, then press the Enter key. 2. Do not use different types of batteries together, or mix old and new batteries. Caution for battery usage Please follow these instructions to install the batteries. Uninstall: 1. Click the Start button on Windows Taskbar, and choose Programs > DSC-1. 3M Smart> DSC-1. 3M Smart Uninstall 2. Follow the uninstall steps 3. restart computer 2. Connect DSC-1. 3M Smart to your Computer 1. When prompted, connect the DSC-1. 3M Smart Camera to the USB port of your computer, as shown in the drawing. 1. Check the polarity marks on the battery ( + and - ) before loading the batteries in the camera. 2. Turn the camera off before removing the batteries. USB connector Getting to Know Your Camera follows: Front view 1. Battery Cover Loading the Batteries 1. Turn off the power of the camera. 2. Open the Battery Cover. then insert the batteries as shown on the inside of the cover. 3. Close and lock the battery cover. NOTE: We recommend that you gently open the battery cover to avoid damaging it. Button Modes Shutter button: Press this button to take pictures or to capture video. Select button: Press this button to change mode in the required function. Power/Mode button: Press this button to power on your camera or switch to required function. The sequential order of functions is as Auto Power OFF Function If no operation is carried out for a fixed amount of time (about 30 seconds), the power is turned OFF to prevent battery wear. This is called Auto Power OFF. Battery Life Indicator (1) Note: If your batter power is low, you can't use the Flash light any more but you still can use the camera. Full Battery Power (2) Low Battery Power Basic Operation Turn on the power of the camera. Press and release the Shutter button to take a picture. (At this time, you will hear one beep. ) The LCD will display and add up the number of pictures taken. When the internal memory is full, the camera will beep, then you will see FULL appears on the LCD. No photos can be taken after this. LCD Description (1) (2) Turn on the power of the camera. Movie recording (1) Three Auto-Shot Mode (2) Self-Timer Press Mode button once and you will see this icon flash. Then press Select button until the icon of Capture appears. Press Shutter button to confirm and press it again. The camera will start to record video. (3) Flash (4) Motion Movie Mode (3) (4) (5) Still Image Mode Press Shutter button to stop recording. Recorded images will be saved in the camera with the AVI file format. You can use the USB cable to download images to a PC. (6) Still Image Quality (7) Still Image Resolution (8) White Balance Mode Three Auto Shot Press the Mode button once and the icon flashes. Then press the Select button until the icon appears. Press Shutter to confirm, then press Shutter again, the camera will take a picture three times automatically. (9) Image/Movie Counter (10) Delete e (11) Battery Life Indicator Image Resolution Press the MODE button twice and you will see the Press the Select button to change the Resolution mode. F(Fine): High Quality: default value N(Normal): Low Quality icon flash. Power On/Off Press the Power/Mode Button and hold it for a second. The power is on after you hear beeps. White Balance Mode Press the Mode button five times and the icon flashes. Then you can press the Select button to change White Balance Mode. Using the Self-Timer Press the MODE button once Auto: Sunny: Cloudy: and you will see the icon flash. [. . . ] If not, please install it first. blinking, your camera has been charged. Now you can use the flashlight. Auto Flash Mode: The camera will detect light automatically. If you are someplace with enough light, the Flashlight won't be enable. Auto Flash Mode Force Flash Mode: The Flashlight will enable no matter where you are. Note: During charging, the FLASH indicator blinks. Charging is completed when the FLASH indicator Force Flash Mode stops blinking. [. . . ]