User manual GENIUS METALSTRIKE FF

[. . . ] Layout of the Sound Maker Value 4. 1 PCI Sound Card AUX LINE IN M IC F-O ut R -O ut C D -IN J1 J10 J8 J9 J6 J3 J4 C M I8738/PCI-SX G A M E /M ID I JP2 llllllllllllllllllllllllllllllllll llllllll Layout of the Sound Maker Value 5. 1 PCI Sound Card AU X C D -IN LINE IN M IC F-O ut R -O ut C/LFE J1 J10 J8 J11 J7 J6 J3 J4 2 6 JP1 J9 J12 C M I8738/PCI-6C H JP3 1 5 G AM E /M ID I JP2 llllllllllllllllllllllllllllllllll llllllll 4 PCI Sound Card－Sound Maker Value 4. 1/5. 1 Sound Card LINE IN MIC F-Out R-Out ＊C/LFE GAME/MIDI CD-IN This connector provides Line-in function. This connector provides Microphone-in function. This connector provides Front sound source output, you can connect one set of active speaker or headphone. This connector provides Rear sound source output, you can connect one set of active speaker or headphone. This connector provides Center & Subwoofer (LFE) sound source output, you can connect one set of active speaker. （＊Value 5. 1 only） The 15-pin female connector can be connected to any IBM PC compatible joystick with a 15-pin D-shell connector and MIDI instrument. [. . . ] If Auto Run can’t be used with your computer, please refer to each Windows as follows, Installing the Sound Card Driver under Windows® 98/98SE 1. After hardware installation has been finished, power up your computer and wait for Windows® 95/98/98SE to boot up. The message box will show “Add New Hardware Wizard” and “This Wizard searches for new drivers for PCI Multimedia Audio Device”. Insert the Multimedia Software CD-ROM into your CD-ROM drive or DVD-ROM drive. Click “Start” at Windows bottom left corner. Key in the drive and path for drivers/application installation program; for example, “D:\SMVALUE4. 1\SETUP. EXE” or “D:\SMVALUE5. 1\SETUP. EXE”. (If your CD-ROM drive or DVD-ROM drive is D) 7. Click “OK” to start the applications/driver installation procedure, and follow the on-screen instructions to finish the installation. When all the application software has been installed, please restart your computer. Your system will install device drivers automatically. Installing the Sound Card Driver under Windows® Me 1. After hardware installation has been finished, power up your computer and wait for Windows® Me to boot up. Click “Start”, Select “Settings”, and click the “Control Panel”. Select “Devices”, and press “Add”. Select “Unlisted or Updated Driver” in “List of Drivers” then click “OK”. Specify the drive and the path where NT drivers are in (such as D:\Smvalue4. 1\Win_NT40\Drv or D:\Smvalue5. 1\Win_NT40\Drv). Select “C-Media PCI Device” and click “OK”. Now, you have already installed the PCI Audio driver under Microsoft® Windows NT® 4. 0 6 PCI Sound Card－Sound Maker Value 4. 1/5. 1 Sound Card successfully. If you want to install the Windows applications, continue the following steps: 12. Key in drive and path for Windows NT® application installation program; for example, “D:\Smvalue4. 1\Win_NT40\App\Setup. exe” or “D:\Smvalue5. 1\Win_NT40\App\Setup. exe”. Click “OK” to start the installation procedures, and follow the on-screen instructions to finish the installation. When all of application software has been installed, shut down the Windows NT® system and then reboot your system. Uninstalling the Sound card Driver for Windows NT® 4. 0 1. Select "Settings" and click "Control Panel". [. . . ] Please check the detail steps from folder “D:\Smvalue4. 1\Linux\Readme file” or “D:\Smvalue5. 1\Linux\Readme file”. Installing the Sound Card Driver under DOS 1. Insert the Multimedia Software into your CD-ROM drive or DVD-ROM drive. Change directory to DOS driver folder (“D:\Smvalue4. 1\Dosdrv” or “D:\Smvalue5. 1\Dosdrv”) at DOS prompt, and type “INSTALL”. Type DOS utilities path that you want to install the file in. [. . . ]