User manual GENIUS VIDEOWONDER DVB

[. . . ] ANT: Use this connection to connect your home or room antenna. The Remote Control 1. Full Screen 2. Full Screen: Switch between Full Screen and previous size 2. Power: Turns on/off the Genius DTV Program 3. [. . . ] This would give both cards the same interrupt, which can lead to crashes during operation!The numbers assigned to the PCI slots are listed in your motherboard manual. 5. Carefully remove the card from its packaging and pick it up by the edges with one hand while your other hand is touching a metal part of the PC. English This will ensure that your body is completely discharged via your computer without damaging the TV card. Align the holder at the rear of the TV card in the expansion slot in such a way that the card's connectors are directly in line with the slot's socket. 7. Push the DVB-T card firmly into the slot, ensuring good contact. 8. Fasten the DVB-T card with an appropriate screw. 9. Reinstall the cover of your PC case. 10. Connect the portable antenna cable or the UHF/ VHF antenna cable (which you would normally connect to the antenna input terminal on your television) to the TV antenna terminal on the DVB-T card. Reconnect the AC power cable as well as all other cables. Make sure that your speakers are set to low volume. English 11. Switch your computer on again to begin installing the software. 3. 3. Driver Installation for Windows® 2000(Service Pack 4) / Windows® XP (Service Pack 1) After rebooting, Windows® 2000(Service Pack 4) / XP (Service Pack 1) will automatically detect the presence of a new hardware component in the system and will tell you so in a "Found new Hardware Wizard" window. If you are not sure what version of Windows you have, just click the right mouse button on "my computer" folder and select "Properties" to see the version. If your PC is not ether Windows® 2000 (Service Pack 4) or Windows® XP (Service Pack 1), please go to Microsoft's website (http://www. microsoft. com) to upgrade your Windows version of Service Pack 4 for Windows® 2000 or Service Pack 1 for Windows® XP by the Internet. This is an example for checking the version of Windows 2000. English If you have not already done so, place the Installation CD into your CD-ROM drive. Then select the "Install from a list or specific location (Advanced)" item and click "Next". Now select "Search for the best driver in these locations. " item and click "Next". Windows will now find the drivers on the Installation CD and install them automatically. After installing the driver, Windows will inform you that it has done so successfully. This completes the installation of the drivers and you can now start installing the application program. 4. Installation of Genius DTV (Digital TV) The installation of the Genius DTV software can be carried out by using either the Auto start program of the provided Driver and Application CD ("Software Installation"), or by executing a single file if you have downloaded the program from the Internet. If the Auto start program does not appear automatically when you insert your Genius Installation CD, start it manually by running the "InstallCD. exe" file located on the Genius Installation CD. English 4. 2. Scanning for TV Channels Before you can watch Digital TV, you have to scan for available channels in your area. To access the Scan Button click in the Window title bar on Tools -> Scan Receiving Setup: Click on terrestrial scanning, so you can enter the minimum and maximum frequency area that can be scanned for channels. Channel Scan: You have two possibilities to scan for available channels: 1. Auto Scan: From the Drop-Down field you can select your country Button. During the Auto Scan, you will see the above picture showing you the actual status. Transponder Scan: English If you have already successfully scanned for channels and you want to add another frequency manually, type in the section for Transponder Scan the frequency in kHz, and the modulation (for DVB-T 16QAM or 64QAM in most cases) and press the Button again. The found channels are displayed in the window, with additional information of TID, SID, Video PID and Audio PID. Here you also have the possibility to save your frequency list, and to import it again. [. . . ] By clicking on the "Add" Button, the settings are saved to the Schedule List. 8. 3 The TimeShift Button English With the TimeShift function, you can pause live TV, leave, and come back and watch your program right where you left it. You can then also fast forward past commercials, or rewind to see a particular scene again. To begin TimeShift, simply click the TimeShift button. The TimeShift button will then turn into a Pause/Play button, letting you pause the video, and then clicking it again will begin playback right where you left it. [. . . ]