User manual GEONAUTE SYNKRON 200

[. . . ] cover damage from misuse, · This guarantee does not the precautions resultingnor from accifrom a failure to observe for use, dents; neither does this guarantee cover damage resulting from improper maintenance or from use of the device for commercial purposes. This warranty does not cover damage resulting from repairs carried out by persons not authorized by Geonaute. The guarantees contained herein explicitly replace all other guarantees including the implicit guarantee of merchantability and/or suitability for use. Geonaute cannot under any circumstances be held liable for any damage, whether direct or indirect, general or specific, caused by or related to these instructions for use or the products they describe. [. . . ] Do not place them near electromagnetic sources (televisions, computers, cordless telephones, electrical equipment) that may impair their functioning. Never use an abrasive or corrosive cleaner on this device. Abrasive cleaners may scratch the plastic parts and corrode the electronic circuit. Used batteries in contact with new ones could leak. 17 RECYCLING The "crossed-out trash can" symbol means that this product, as well as the batteries it contains, is made of recyclable materials. They should not be disposed of with municipal waste. When the batteries and electronic product are worn out, return them to a recycling or collection facility. This treatment of your electronic waste will protect the environment and your health. EN FIRST USE IMPORTANT: This paragraph is crucial to ensuring proper use of the device. It is very important to follow the instructions step by step when using the station for the first time. Do not skip any steps or do them out of order. In case of problems, you can always come back to this procedure to reset the whole system and get a fresh start. Startup procedure It is important to start the initializing or problem-solving procedure according to the precise configuration described below. The following checklist must be followed in the right order. Note that once a channel has been assigned to a sensor, you can change it only by removing the batteries or resetting the unit. Insert the batteries in strict accordance with the polarities as indicated in the battery compartment. Put the battery compartment cover back on and re-tighten the screws. Once the batteries have been inserted in the sensor, data transmission will occur in thirty-second intervals. 20 EN Note: For both the remote sensor and the main unit, change the batteries as soon as they are low. B. Mounting the remote sensor The remote sensor is equipped with a wall mount that can be attached to the wall with two screws (A). It can also be placed on a horizontal surface with the folding table stand. (B) A B IMPORTANT: The sensor and the station must be placed in an upright position for the signal to be transmitted properly ! TRANSMISSION DISTANCES IMPORTANT: The maximum signal transmission distances vary with the surrounding materials and electromagnetic interference. 21 The table below describes typical distances in different situations : Outdoors, no obstacles 20-30m Small obstacles (window, plywood door, wooden table, couch) Electric devices (stereo system, TV, computer, washing machine, microwave) Radio devices, satellite antenna, cell phone Brick walls 15-20m 10-15m 10-15 m with risk of random disconnections 10-15 meters Reinforced concrete wall, several walls 5 m or no transmission SPECIFICATIONS Re-initializing/RESET Button (E) is to be used if the device is not working satisfactorily or if it malfunctions. All the settings return to their initial default values. You must return to the manual settings and customize the display. B. Comfort level Based on a measurement of temperature and relative humidity (HR), this device determines a comfort level: COMFORT (comfortable), WET(humid), or DRY (dry). This comfort indicator is displayed when the following conditions occur together: 22 EN Comfort indicator displayed on device Indoor temperature range 20°C to 25°C (68°F to 77°F) Humidity range 40% RH to 70% RH Greater than 70% RH Lower than 40% RH Condition of indoor environment Ideal state for indoor temperature and relative humidity Too humid COMFORT WET Total range DRY Total range Too dry No indicator Lower than 20ºC (68ºF) 40% RH to 70% or higher RH than25º C (77) C. Maintenance Here are a few tips on maintaining your sensor : · Never submerge this device. [. . . ] Operation of this device is subject to the following two conditions: 1. There is no risk of this device producing harmful interference. This device must accept any interference received, including interference which may cause malfunctioning. This equipment has been tested and recognized as meeting the limits of class B digital devices, pursuant to section15 of the FCC regulation. [. . . ]