User manual GEONAUTE WATCH CHRONO 700

[. . . ] time, stopwatch time Lap, split timer [000] RECALL LAP SLOW STOP FAST PACER AVG SPLIT Memory : slowest lap, fastest lap, average lap time Down'n'Up countdown indicator Split countdown timer indicator Beep indicator 00:00':00''00 00:00':00'0' 0 TIME BPM Secondary data, e. g. SPLIT, year : SPLIT/RESET, RECALL, START/STOP MODE, LIGHTNING. , · 5 buttons lines · 3 display precision to 1/100 of a second up to 10 hours · measuring batteries (CR2032). · Replaceable · Case is waterproof to water spray. [. . . ] Press on any button to 20 21 3 Pacer mode (PACER) 4 Countdown Mode (TIMER) 00:26':06''83 PACER PACER''00 180''00 BPM [001] STOP 04:00TR1'0' 0 00:30':00'0' 0 START/STOP : start / stop the pacer RECALL : decrease the pacer value SPLIT/RESET : to increase the frequency of the pacer MODE : go to the following mode Display ·Top line: :displays the stopwatch if it is active. - Middle line : PACER - Bottom line: pacer frequency. In this mode, the screen displays word PACER in the middle the screen. · The letters BPM (beats per minute)thefound on the lower right of theofscreen. · The alarm symbol will appear if it isisselected (see corresponding mode). · The word PACER will flash at the bottom left of the screen if it is activated. · On the bottom line, you will read the value of the rhythm set, from 01 to 240 pulsations · per minute (possible values: 1, 2, 3, 4, 5, 10, 15, 20, 30, 40, 50, 60, 80, 100, 110, 120, 130, 140, 150, 160, 180, 200, 220, 240) START/STOP : to start/stop the TIMER RECALL : to enter the setting mode SPLIT/RESET : to set the values MODE : go to the following mode Display: ·Top line : the current value of the countdown. - Middle line : TR, number of the countdown and repetition counter. - Bottom line: starting value of the countdown. top line, · On the: seconds :you will readofthe current value of the countdown (format - hour : minutes hundredths seconds). you will read the set value of the countdown (format - hour : minutes the middle to left the · Inthe countdown thethreeofdigits. screen will appear the indication of the repetition counter for to pictogram indicating · On the lower left of the screen, (ina all the modes) whenthe type of countdown that is the countdown is activated. This pictogram will flash · A « STOP » pictogram is displayed when the countdown has stopped. There are 3 possible countdown modes: Down and Up : the countdown starts at the starting value, goes down to 0, emits a beep, and then begins the stopwatch at the beep. Repeated timer : repeated countdown: the countdown starts at the starting value, goes down to 0, beeps, and then begins again from the starting value. The repetition counter increases each time. Training timer : countdown for training. You can set up to 9 different, successive countdowns. You will also set the number of repetitions of the sequence thus formed. You may go from one to the other by pressing for a longer time on the SPLIT/RESET button. · Setting the rhythm value. to scroll through the pacer values incrementally. Press Press the SPLIT/RESET button RECALL to scroll downwards. Press the START/STOP button to start or stop the pacer. When the pacer is activated, the word PACER will flash. · · · · 22 23 Down and up timer (symbole ) · Use : The START/STOP button starts or stops the countdown. When the countdown has stopped, press the SPLIT/RESET button to reinitialize it at its set value. When the count arrives at 0, a 5 second buzz is emitted. [. . . ] The order of reading is different depending on whether the stopwatch is functioning or not. If the stopwatch is functioning : By pressing RECALL repeatedly, scroll through the values already put into memory in the following order : - The fastest lap time (FAST) - The slowest lap time (SLOW) - The average lap time of the X measurements recorded (AVG) - The last lap time (x) - The next to last lap time (x-1) . . . - Le 1er temps au tour (1) If the stopwatch is not functioning : By pressing RECALL repeatedly, scroll through the values already put into memory in the following order : - The fastest lap time (FAST) - The slowest lap time (SLOW) - The average lap time of the X measurements recorded (AVG) - The FIRST lap time (1) - The SECOND lap time (2) . . . - The next to last lap time (x-1) - The last lap time (x) · · Once the stopwatch has stopped, the word STOP will appear to the left of the screen. [. . . ]