User manual GEONAUTE WATCH CONO TRTL 500

[. . . ] · Case is waterproof to water spray. May be used for water sports or in the rain. · Functions Stopwatch for and 59 minutes · Time (h, min, sup to 99 hourshour display) in 12 and 24 · Date (day, month, year), automatic calculation of the day of the week (from 2000 to 2049) · 10 intermediate times (laps) · 10 functioning memories that can be consulted, calculation of the fastest LAP and the slowest LAP · 2 countdown systems (TIMER) that can be set for from 1s to 99h59min59s in steps of 1 · and decrementation to 1/100s s · Pacer (PACER) that can be set for from 01 to 240 beeps per minute Description of normal conditions of use This stopwatch has been designed to measure intervals of time in order to optimize athletic training or for measuring performance. [. . . ] On the bottom line, the date in day week-month format, day of the month (time in AngloSaxon mode). The day of the week is automatically calculated depending on the year and date selected (years 2000-2049). Batteries : The stopwatch uses a CR2032 type battery. 14 15 and date. · Settingathe timetime (2s) on the RECALL button. The word SET and the number for the Press for longer hours will flash to indicate that you have entered the setting mode. When one of the elements flashes, press the START/STOP button to make the numbers scroll until you reach the desired value. Press RECALL again to leave the setting mode. When the alarm goes off, it sounds for 20 seconds. Press on any button to stop the sounding. · Press the SPLIT/RESET button repeatedly to change the parameter to be set, following the sequence . . . Hour-minutes-seconds-year-month-day. When one of the elements flashes, press the START/STOP button to reset the seconds to 0 or make the numbers of the parameter scroll until you reach the desired value. Hold the button down to set more rapidly Press RECALL again to leave the setting mode. · 3 Stopwatch mode SPLIT 2 Daily Alarm Mode [000] RECALL SLOW FAST LAP STW AL AM:12:0000 TIME 00:00':00'9' 7 00:00':09'2' 4 AM:12:1333 START/STOP : start/stop the stopwatch RECALL : recall of intermediate times recorded SPLIT/RESET : to record an intermediate time MODE : go to the following mode Display : ·Upper line: the current value of the stopwatch and, if needed, SPLIT - Bottom line: LAP, the time for this lap In this mode, the screen will display the letters STW in the middle of the screen (flashing) when the stopwatch is functioning and STOP when it has stopped. Once the stopwatch has stopped, the word STOP will appear to the left of the screen. The stopwatch measures the intermediate times (SPLIT, the time that has passed since the start up to the given point in time) and the time for the lap (LAP, the time that has passed since the last partial measurement of time up to the given point). It measures and saves the first 10 measurements of intermediate time in memory. DÉPART START LAP 1 SPLIT 1 SPLIT 2 SPLIT 3 END : SPLIT 4 17 LAP 2 LAP 3 END : LAP 4 400 m 800 m 1200 m 1500 m START/STOP : activate/deactivate the alarm RECALL : to enter the setting mode SPLIT/RESET : inactive MODE : go to the following mode Display ·Top line ::Wake-up time - Bottom line : Time · · · The symbol for the daily alarm will appear if the function is selected (see corresponding chapter). The ALARM symbol will appear for several seconds upon arriving in this mode, and then remain displayed on the top line. will read the time · On the bottom line, you12h or 24h mode. displayed according to the setting, as seen in the preceding chapter, in On the top line, the alarm time will appear in the same format as that of the time, which was set in the time date mode. · Press the START/STOP button to alternate between activating and deactivating the alarm. · Set theaalarm : time (2s) on the RECALL button. The word SET and the number for the Press for longer · 16 alarm hours will indicate that you have entered the setting mode. Press the SPLIT/RESET button repeatedly to change the parameter to be set, following the sequence . . . Hour-minutes-. . . The current value of the stopwatch is displayed on the top line. (format - hour : minutes : seconds : 1/100s). [. . . ] On the lower line, you will read the value of the countdown setting (format - hour : minutes : seconds) At the top left of the screen will appear the indication of the repetition counter for the countdown to three figures. At the bottom left of the screen, a pictogram indicates the type of active countdown. The word TIMER will flash (in all modes) when the countdown is activated. · · · · · · Contact As we strive to continually improve the products we develop, we are interested in your feedback regarding the quality, the functionality and the usage of our products. [. . . ]