User manual GEONAUTE WATCH OUTDOOR 500WW

[. . . ] - This guarantee does not cover damage resulting from misuse, from a failure to respect the precautions for use nor from accidents; neither does this guarantee cover damage resulting from improper maintenance or from use of the item for commercial purposes. - This warranty does not cover damage resulting from repairs carried out by persons not authorized by GEONAUTE. - The guarantees contained herein explicitly replace all other guarantees including the implicit guarantee of fair and trade quality and/or adaptation to use. GEONAUTE cannot under any circumstances be held responsible for any damage, be it direct or indirect, general or specific, caused by or related to these directions for use or the products they describe. [. . . ] · Press on S3: the hours will flash. Proceed in this manner to successively set the minutes, the seconds, the year, the month and the day of the month. S4 24 25 EN · Press on S4 at any time to exit time setting mode. The day of the week is calculated automatically within a period from 2003 to 2053. 2 - Alarm mode (ALARM) S1 : activate/deactivate the alarm S2 : activate/deactivate the hourly beep S4 S3 : switch to the next mode. S4 : quick press: S3 electroluminescence long press: set the alarm UV INDEX MI UV LO DISPLAY OF MOON MODES On the watch, an icon indicates the current moon phase. A full cycle of the moon lasts 29. 5 days. The phases are indicated according to the table below: 14. 0 T1 S1 P 12:00AL WE 1-01 S2 3 2 USING THE ALARM 4 · Press on S1: activate and deactivate the selected alarm. · Press on S2: activate and deactivate the hourly beep (chimes). 5 1 SETTING THE ALARM 8 7 6 26 1 - New moon 2 - Waxing crescent 3 - First quarter 4 - Waxing gibbous 5 - Full moon 6 - Waning gibbous 7 - Last quarter 8 - Waning crescent and the cycle starts over until the next new moon · Press on S4 for 2 seconds: enter setting mode and the hour digits will flash. · Press on S1 or S2: set the hours. · Press on S3: the minute digits will flash. · Press on S1 or S2: set the minutes. · Press on S4 at any time to exit setting mode. 27 EN 3 - Stopwatch mode (CHRONO) S1 : start/stop stopwatch S4 S2 : lap time/clear the stopwatch 00'00"00 (long press) S3 S3 : switch to next mode S4 : quick press: electroluminescence long press: enter lap time recall mode UV INDEX MI UV LO The LAP is the time elapsed since the last lap time. 0 S1 14. 0 P STW CHRON S2 Split1 Lap1 Split 2 Lap 2 Split 3 Lap 3 Split 4 Lap 4 USING THE STOPWATCH · Press on S1: start the stopwatch and the STW symbol is displayed while the stopwatch is timing. · Press on S1: stop the stopwatch. · Press for 2 seconds on S2: "RESET" is displayed and the stopwatch is cleared. · Press on S1: start the stopwatch. · Press on S2: measure a lap time, the stopwatch keeps timing. The screen displays the LAP and the SPLIT for 3 seconds then goes back to the display of the current time. · Press on S1: stop the stopwatch. · Press on S2 for 2 seconds: "RESET" is displayed and the stopwatch is cleared. The stopwatch can measure times up to 23 hours, 59 minutes and 59 seconds. LAP TIMES The stopwatch included with this watch features 30 lap times. Each time a lap time is measured (quick press on S2 while the stopwatch is running) the watch will save the elapsed time (SPLIT) and the lap time (LAP). The SPLIT is the time elapsed since the stopwatch started timing (0) until the lap time. RECALL OF LAP TIMES In stopwatch mode: · Press for 2 seconds on S4 to display the saved lap times. [. . . ] · Press on S1 or S2: set the high tide parameter and the low tide parameter for the next tide. · Press on S3: the hours will flash. · Press on S1 or S2: set the hours. · Press on S3: the minute digits will flash. [. . . ]