User manual GEONAUTE WS300

[. . . ] A K D H C G RESET B L F E AA UM-3 1, 5V AA UM-3 1, 5V I J G - Resetting/RESET control Resets all the settings to their default values. H - °C/°F control Selects Celsius (°C) or Fahrenheit (°F) degrees. I ­ Battery housing Housing for the two alkaline LR6-AA, 1. 5V batteries. J ­ Removable base For placing the device on a flat surface. [. . . ] Make sure that the temperature-signal receiving indicator is displayed (see corresponding section). If the temperature is not displayed, press on the SEARCH button. RESET AA UM-3 1 UM-3 1, 5V RESET AA UM-3 1, 5V AA UM-3 1, 5V RESET UM-3 1, 5V RESET UM-3 1, 5V AA UM-3 1, 5V AA UM-3 1, 5V AA UM-3 1, 5V AA UM-3 1, 5V 6- To enter time setting mode, press on the MODE button for 3 seconds. Change the parameters with the arrows located on the back of the device and change the parameter to be set to by briefly pressing on the MODE button. 7- Place the station and the sensors in their permanent locations. Make sure to position the sensors upright and not to exceed the distances recommended in the instructions, depending on whether there are obstacles between the sensor and the station or not. RESET 8- Check that the outdoor temperature is displayed and that the transmission signal shows that temperature data is being transRESET mitted. UM-3 1, 5V AA UM-3 1, 5V AA UM-3 1, 5V 15 Batteries Installing the batteries in the remote sensor The remote sensor runs on two AA (LR6) 1. 5 V batteries. To install them: · Unscrew the cover of the battery compartment. · Insert the batteries strictly according to the polarities as indicated in the battery compartment. · Put the battery compartment cover back on and reinsert the screws. Once the batteries have been inserted in the sensor, data transmission will occur in intervals of 78 seconds. Installing the batteries in the main unit. Once you have installed the batteries in the remote sensor, you can install the two AA (LR6) batteries in the main unit. To do so : · Gently remove the battery compartment cover. · Insert the batteries strictly according to the polarities as indicated in the battery compartment. · Put the battery compartment cover back on. RESET AA UM-3 1, 5V AA UM-3 1, 5V Note: For both the remote sensor and the main unit, change the batteries as soon as they are low. The low battery cator is in the indoor/outdoor temperature window and is displayed as soon as the batteries are low. indi- Do not throw the batteries away, as this may be hazardous. Protect the environment by depositing used batteries in an authorized collection area for recycling. 16 Installation · Mounting the main unit This unit can be mounted on a wall using the screw head hole (K). It can also be placed on a flat surface using the table stand. · Mounting the remote sensor The remote sensor is fitted with a two-screw wall mount that can be screwed onto the wall. It can also be placed on a horizontal surface with the built-in table stand. IMPORTANT : The sensor and the station must be placed in an upright position for the signal to transmit properly!The wireless sensor is resistant to splashing but it should never be immersed in water or exposed to heavy rain. Avoid prolonged exposure to direct sunlight and wind. Transmission distances IMPORTANT : The maximum transmission distances of the signal vary according to the surrounding materials and electromagnetic interference. The table below describes typical distances in different situations: Outdoors, no obstacles 20-30m 15-20m 10-15m Electric devices (stereo system, TV, computer, washing machine, microwave) Radio devices, satellite antenna, cell phone Reinforced concrete wall, several walls Brick walls Small obstacles (window, plywood door, wooden table, couch) 10-15 m with risks of random disconnections 5 m or no transmission 10-15 meters 17 The device features 3 display lines for easy reading. Each line has a precise function: · Outdoor temperature · Indoor temperature · time, alarm, calendar. NAVIGATION SYSTEM EXPLANATION OF EACH DISPLAY This window displays the temperature in Celsius (°C) or Fahrenheit (°F) degrees as measured by the wireless sensor transmitting data to the main unit. Use the memory function (MIN/MAX) to display in this window the minimum and maximum temperatures, which have been saved automatically. The respective indicators MAX and MIN are displayed. The icon on the right-hand side indicates the status of the main unit's reception of data transmitted by the remote sensor. [. . . ] move the sensor away from this source of temperature interference. 1 The station is not displaying the temperature measured by the sensor. ---. - is displayed in the "outdoor temperature" field 2 The temperature is displayed, but is very different from the expected value. 3 The time indicated is different from the actual time 1. Set the time manually as specified in the relevant procedure For any other problems than those described above, or for any problems you cannot solve alone, place the station and the sensor on a table and carry out STEP by STEP the initializing procedure as described in the Gettin' Started section. IMPORTANT!!! Resetting/RESET The order in which the steps are carried out is VERY IMPORTANT. Use the G button if the device is not working satisfactorily or if it is malfunctioning. All the settings return to their initial default values. [. . . ]