User manual GERICOM 85P

[. . . ] Notice The company reserves the right to make any updating, revisions or changes to the information contained herein as and when deemed necessary. The company is under no obligation to notify any purchaser or end-user of such actions in advance or afterwards. 1998 User's Manual Trademarks IBM PC, OS/2, PS/2, EGA, and VGA are registered trademarks of International Business Machines Corporation. Intel, Pentium are trademarks of Intel Corporation. [. . . ] This saves time and battery power. Caution: Do not enter suspend mode when you are 1. Accessing any of the disk drives, such as HDD, FDD or CD-ROM drives. Using the audio features or playing back video. Playing a DOS game. Powered On Suspend (POS) Of the suspend modes, Powered-On-Suspend saves the least amount of power. However, it takes the shortest time to return to full operation. Resume from POS Mode The system can resume from Powered-On-Suspend mode by: Alarm resume (month/day/hour/minute) Modem ring Pressing any keyboard key. Pressing the power button (if configured as Suspend/Resume function under SCU) Opening the display lid (only if the suspend mode is initiated by closing the display lid) User's Manual Chapter 2: Operation 2-25 Suspend To Disk (STD) Suspend to Disk is a 0-volt suspend mode for system power management. STD mode saves the maximum power but takes the longest time to return to full operation. 1. Use your operation system's FDISK program to delete all partitions of the hard disk if any already exist on the target drive. 2. Boot the system and run the 0VMAKFIL. EXE Utility to create the Suspend to Disk partition on the hard disk. The size of Suspend to Disk partition will be the installed DRAM (n) plus 8MB integrated video RAM. :\>0VMAKFIL ­Pn For example, if the system DRAM is 32MB, 0VMAKFIL will create a partiton size of approximately 40MB. :\>0VMAKFIL ­P32 Resume from STD Mode The system will resume from Suspend-To-Disk mode by: · · · Power back on Alarm resume (month/day/hour/minute) Opening the display lid (only if the suspend mode is initiated by closing the display lid) User's Manual Chapter 2: Operation 2-26 Attaching Peripheral Devices To extend the computer's functions, you can attach the following peripheral devices to the computer through the ports or jacks on the rear panel of computer. Attaching a Security Lock The security lock is equipped to protect your computer from being stolen. To install the security lock, wrap the cable around a desk or other immovable object, then insert the locking device into the connector (Figure 2-20). Figure 2-20 User's Manual Chapter 2: Operation 2-27 Attaching a Parallel Printer You may connect any standard Centronics parallel printer to your computer through the parallel port. 1. Connect the cable to the parallel port on the rear of the computer. Tighten the screws that fasten the cable to the parallel port (Figure 2-21). 4. Insert the other end of the cable to the printer's connector. Fasten the cable's connector. 5. Turn on the printer and computer. In addition, you also need to install the manufacturer-supplied driver for the printer. Refer to the device's user's guide for more information. If the connected printer supports EPP (Enhanced Parallel Port) or ECP (Extended Capabilities Port) mode, please enter System Configuration Utility (SCU) to configure the required setting. Figure 2-21 User's Manual Chapter 2: Operation 2-28 Attaching a TV Set The S-Video jack on the rear panel of the computer is used for transmitting video signals to a TV set. You may need to select the video standard for video display. Enter the System Configuration Utility (SCU), Components Menu to specify the appropriate TV mode. [. . . ] Run "setup. exe" to finish installation. Note: When ATI VGA driver has existed in WIN95 system, click "Start", select "Run", open the path "atiuinst-clean", and then double-click "OK" to finish installation. Step 2: Installing Audio Driver (1978S M2E) Double click "Start". Remove "PCI Multimedia Audio Device". Click "OK", then restart the system. [. . . ]