User manual GIGABIT WEB SMART

[. . . ] 4 1. 3 Package contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 1. 4 Front panel LED indicators. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 1. 5 Rear panel. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 1. 6 Power Connecting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] 38 3. 3. 1 Command Hierarchy . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38 3. 3. 2 Login/Logout Procedures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39 3. 3. 3 Help Utility. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39 3. 3. 4 Example. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39 3. 3. 5 Entering Commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Introduction 1. 1 General Description The device is a full-featured 24-port Web Smart Gigabit Ethernet Switch that provides Ethernet direct connection to local area network or individual PC with build-in 24-port switch. The device uses advanced Gigabit Ethernet chipset solution with complete set With a 46Gbps internal of industry standard features for high-speed Internet access. linking to backbone or high capacity of servers. switching fabric, the Switch is able to handle large amounts of data in a secure topology The device can recognize up to 8K MAC Address Table and provide 480KB on-chip buffer memory. The device also provides Smart management functions through the Web management interface, such as per port speed, duplex, flow-control settings and QoS settings, Trunking and port-based VLAN, port mirroring, all of these can be found in the GUI of your web browser. The Web Smart Gigabit Ethernet Switch offers easy installation and cost-effective connection for corporate and government users. The product is made in ISO9001 approved factory. This Web Smart Gigabit Ethernet Switch complies with FCC part15 regulations and CE approval. 1. 2 Product Features Supports 24 10/100/1000Mbps Gigabit switching ports Supports 10/100Mbps Half/Full duplex and 1000Mbps Full duplex, flow control and auto-negotiation Supports IEEE 802. 3x flow control for Full Duplex mode and back pressure for Half Duplex mode Supports automatic address learning and address aging Supports Store-and-Forward architecture Supports auto MDI/MDI-X function Supports up to 9KB Jumbo Frame Supports up to 8K MAC Address Table Provides 480KB Buffer Memory Remote Web management interface RS-232 port command line interface Supports System log, view trap, IP setting through Web management utility, 4 firmware upgrade Supports Port-based VLAN, Tag-based VLAN, Trunk, Port Mirroring, QoS Supports Supports Supports Supports SNMP, LACP, RTSP, IGMP Snooping. 802. 1X Storm Control (ICMP, Broadcast, Multicast, Flooded unicast) Supports backup and restore current configuration 1. 3 Package contents 24-Port Web Smart Gigabit Ethernet Switch AC Power Cord Installation CD Two Rack-mounted Brackets Eight Screws *If any of the items is damaged or missing, please contact your retailer immediately. 1. 4 Front panel LED indicators After installing the switch, you can check its status from the LED indicators on the front panel shown below. [For 24-Port Switch] LED PWR 10/100M LINK / ACT 1000M LINK / ACT STATUS Color GREEN YELLOW GREEN Status ON OFF ON BLINKING ON BLINKING ON ON Indication The switch is power on The switch is power off A link of 10/100Mbps is established A link is established and data is being transmitted or received A link of 1000Mbps is established A link is established and data is being transmitted or received System is ready System boots GREEN ORANGE 5 1. 5 Rear panel Rear Panel of the Switch has a RS232 Connector, a power cord socket. 1. 6 Power Connecting Plug the circle end of the power cord firmly into the power port on the switch rear panel, and the other end into an electric service outlet, then the system is ready. 1. 7 Connecting computers to the switch The switch features auto-MDI/MDIX crossover detection function and provides plug-and-play capability. Users can immediately use any of the features of this product simply by plugging the network cables (RJ-45) into the computers and the 1. 8 Uplink All Ports can be used as an uplink port for connecting to another unit without using crossover cable. When using the uplink port, you can extend the distance to 100m for linking another switch or hub. 1. 9 To prolong the operational life of your units *Never stack units more than eight high if freestanding *Do not place objects on top of any unit or stack *Do not obstruct any vents at the sides of the case 6 2. Installing the Web Smart Gigabit Ethernet Switch 2. 1 Configure system network The Web Smart Gigabit Switch offers a Web based management software to manage and monitor the Switch. Before running the management software, you have to configure your system network setup. For Windows 98/98SE and ME, click "Start configure system network setting. For Windows 2000 and XP, click "Start Internet Connections in Windows XP: Step 1: Right click "LAN" icon, and then select "Properties". Control Panel Network and Settings Control Panel", double click "Network" icon, select "Configuration" tab then choose "TCI/IP" to Network Connections", then right click LAN icon to configure system network setting. Forward Delay: You can change forward delay time, the number of seconds a port waits before changing from it Spanning-Tress protocol learning and listening states to the forwarding state. [. . . ] <enter> Commands at top level: System Console Port MAC VLAN Aggregation LACP RSTP User Group QoS Mirror IP Dot1x -- System commands -- Console commands -- Port commands -- MAC table commands -- VLAN commands -- Aggregation/Trunking commands -- IEEE 802. 3ad Link aggregation commands -- IEEE 802. 1w Rapid Spanning Tree commands -- User Group commands -- QoS commands -- Mirror commands -- IP commands -- Dot1x commands 39 Debug -- Debug commands > console <enter> Console> ?<enter> Commands at Console level: Console Password [<password>] Console Timeout [<timeout>] Console Prompt [<prompt string>] ----Up Console> password ?Syntax: Console Password [<password. ] Description: Set or display console password. The empty string (" ") disables the password check. [. . . ]