User manual GIGABYTE 飄流機

[. . . ] GA-K8N51GMF-9 AMD Socket 939 Processor Motherboard User's Manual Rev. 1004 12ME-51GMF9-1004R * The WEEE marking on the product indicates this product must not be disposed of with user's other household waste and must be handed over to a designated collection point for the recycling of waste electrical and electronic equipment!!* The WEEE marking applies only in European Union's member states. Motherboard GA-K8N51GMF-9 Motherboard GA-K8N51GMF-9 Sept. 29, 2005 Copyright © 2005 GIGA-BYTE TECHNOLOGY CO. , LTD. [. . . ] Monitor CPU temperature at 70o C / 158oF. Monitor CPU temperature at 80o C / 176oF. Monitor CPU temperature at 90o C / 194oF. (Default value) Disable System/CPU fan stop warning function. (Default value) Enable System/CPU fan stop warning function. System/CPU FAN Stop Warning CPU Smart FAN Control (Note) Disable this function. (Default value) When this function is enabled, CPU fan will run at different speed depending on CPU temperature. Users can adjust the fan speed with Easy Tune based on their requirements. (Note) Whether the CPU Smart FAN Control function is supported will depend on the CPU you install. For more detailed information please check at the FAQ section on GIGABYTE's website. GA-K8N51GMF-9 Motherboard - 42 - 2-7 Frequency/Voltage Control CMOS Setup Utility-Copyright (C) 1984-2005 Award Software Frequency/Voltage Control CPU Frequency PCIE Clock K8 CPU Clock Ratio Robust Graphics Booster [200. 0] [100Mhz] [Default] [Auto] Item Help Menu Level English : Move Enter: Select F5: Previous Values +/-/PU/PD: Value F6: Fail-Safe Defaults F10: Save ESC: Exit F1: General Help F7: Optimized Defaults Incorrect using these features may cause your system broken. For power end-user use only. CPU Frequency 200. 0~300. 0MHz Set CPU Frequency from 200MHz to 300MHz. Set PCIE Clock from 100MHz to 145MHz. PCIE Clock 100~145MHz K8 CPU Clock Ratio This setup option will automatically assign by CPU detection. (Default value: Default) Robust Graphics Booster Select the options can enhance the VGA graphics card bandwidth to get higher performance. Auto Set Robust Graphics Booster to Auto. (Default value) Fast Set Robust Graphics Booster to Fast. Turbo Set Robust Graphics Booster to Turbo. - 43 - BIOS Setup English 2-8 Load Fail-Safe Defaults CMOS Setup Utility-Copyright (C) 1984-2005 Award Software Standard CMOS Features Advanced BIOS Features Integrated Peripherals Power Management Setup PnP/PCI Configurations PC Health Status Frequency/Voltage Control Esc: Quit F8: Q-Flash Load Fail-Safe Defaults Load Fail-Safe Defaults Load Optimized Defaults Set Supervisor Password Set User Password Load Fail-Safe DefaultsSave & Exit Setup (Y/N)?N Exit Without Saving : Select Item F10: Save & Exit Setup Fail-Safe defaults contain the most appropriate values of the system parameters that allow minimum system performance. 2-9 Load Optimized Defaults CMOS Setup Utility-Copyright (C) 1984-2005 Award Software Standard CMOS Features Advanced BIOS Features Integrated Peripherals Power Management Setup PnP/PCI Configurations PC Health Status Frequency/Voltage Control Esc: Quit F8: Q-Flash Load Optimized Defaults Load Fail-Safe Defaults Load Optimized Defaults Set Supervisor Password Set User Password Load Optimized Defaults (Y/N)?N Setup Save & Exit Exit Without Saving : Select Item F10: Save & Exit Setup Selecting this field loads the factory defaults for BIOS and Chipset Features which the system automatically detects. GA-K8N51GMF-9 Motherboard - 44 - 2-10 Set Supervisor/User Password CMOS Setup Utility-Copyright (C) 1984-2005 Award Software Standard CMOS Features Advanced BIOS Features Integrated Peripherals Power Management Setup PnP/PCI Configurations Enter Password: PC Health Status Frequency/Voltage Control Esc: Quit F8: Q-Flash : Select Item F10: Save & Exit Setup Change/Set/Disable Password Load Fail-Safe Defaults Load Optimized Defaults Set Supervisor Password Set User Password Save & Exit Setup Exit Without Saving English When you select this function, the following message will appear at the center of the screen to assist you in creating a password. Type the password, up to eight characters, and press <Enter>. You will be asked to confirm the password. Type the password again and press <Enter>. You may also press <Esc> to abort the selection and not enter a password. [. . . ] Support : http://tw. giga-byte. com/TechSupport/ServiceCenter. htm Non-Tech. Support(Sales/Marketing) : http://ggts. gigabyte. com. tw/nontech. asp WEB address : http://www. gigabyte. de Japan NIPPON GIGA-BYTE CORPORATION WEB address : http://www. gigabyte. co. jp Singapore GIGA-BYTE SINGAPORE PTE. Support : http://tw. giga-byte. com/TechSupport/ServiceCenter. htm Non-Tech. Support(Sales/Marketing) : http://ggts. gigabyte. com. tw/nontech. asp WEB address: http://www. gigabyte. com. sg U. K. [. . . ]