User manual GIGABYTE 3D MERCURY INSTALLATION DETAIL

[. . . ] Use the product incorrectly or in a manner other than the designed purpose. Nonobservance of the proper operation provided. over-clocking) Malfunction due to interference from other devices. Unauthorized modification of the product. [. . . ] Consequential damage to other objects due to the product's fault. Malfunction arising from casualties (earthquake, thunder, fire, and flood). The product's warranty label has been removed or damaged. The devices inside, including power supply, hard disk, CD-ROM drive, motherboard, ventilator, etc, are not detached from the casing prior to the transportation of the computer product, resulting in damage to the casing or computer-related devices. Any loss caused by failure to follow the installation process contained in the user manual. Any damage to the system arising from coolant leakage due to improper installation. Any damage arising from the use of liquids other than GIGABYTETM Liquid Coolant is not covered by the warranty. 2 English Table content 1 Accessories List 2 Specification Instruction 3 Feature Instruction 4 Liquid Cooling System Installation 4-1 4-2 4-3 4-4 4-5 4-6 4-7 4-8 4-9 4-10 4-11 4-12 4-13 4-14 4-15 4-16 4-17 4-18 5-1 5-2 Installation Preparation Intel Pentium 4 LAG775 Back Plate Installation PCI Rear Fan Speed Controller Installation Tube Installation 4-way Splitter Valve to the Tube on Waterblock Installation Radiator to 4-way Splitter Valve Installation Radiator to the Inlet of Water Tank 4-way Splitter Valve to the Outlet of Water Pump Waterblock Installation Intel Pentium 4 LGA775 Bracket Installation AMD K8 Clip Installation AMD AM2 Clip Installation Fasten 4-way Splitter Valve MOSFET Air Cooling Fan Installation Pump Power Cord Installation Fan Speed Control Box and Power Cord Instruction Fan Speed Control Box Installation Heat Sink Installation Liquid Cooling System Installation and Test Radiator Installation ® ® ® ® 4 6 6 7 7 7 8 8 9 10 11 11 12 12 13 13 14 14 15 16 16 17 18 18 19 20 22 5 Liquid Cooling System Installation and Test 6 Liquid Cooling System Disassembly 7 4-way Splitter Valve Instruction and User Manual 3 English 1. Accessories List (1) Radiator (2) Pump + Tank Assembly (3) MOSFET Air Cooling Fan (4) Waterblock X2 pcs (5) 4 - way Splitter Valve (6) 1 / 2 inch Tube X8 pcs (7) Tube Clips (8) Screws X4 (9) Intel Pentium 4 LGA775 Spring Screws ® ® (10) Intel Pentium 4 LGA775 Back ® ® Plate (11) Intel Pentium 4 LGA775 Bracket ® ® (12) AMD K8 / AM2 Clip (13) AMD K8 / AM2 Bracket (14) Fan Speed Control Box (15) PCI Rear Fan Speed Controller (16) Radiator Rack 4 English X8 pcs (17)Pump Power Cord (18)Fan 1 to 2 Power Cord (19)Fan Speed Control Power Cord (20)Heat Sink for Memory X2 pcs (21)Bend Proof Spring X4 pcs (22)Nylon Tie (23)Grease (24)Gigabyte Liquid Coolant X2 (25)Velcro (26)Quick Installtion Guide No. 8 Screw: a ­ Secure PCI Rear Fan Speed Controller ( 1pc ) b ­ Secure Radiator ( 3pcs ) c ­ Pump + Tank Assembly ( 2pcs ) 5 English 2. Specification Instruction Mosfet cooling fan Fan size Fan speed Fan Connector Bearing Noise Dimensions Maximum Capacity Noise Bearing Life time Dimensions Material Fan size Fan speed Fan Connector Bearing Noise Dimensions Capacity Dimensions Materia Dimension Material Capacity Color 80 x 80 x 25 mm 2000 RPM 3 pin EBR 19 dBA 61 x 60 x 46 mm 400 L/hr 20 dBA Ceramic Bearing 70000 hr (MTBF) 125 x 197 x 64 mm Aluminum 120 x 120 x 25 mm 1200 ~ 2600RPM 3 pin 2 Ball 19~39 dBA 100 x 53 x 172 mm 220cc. inlet:1/2"; outlet:1/4"*2, 1/2"*1 POM 1/2 inch PVC, UV sensitive 600cc. Lite Blue Pump Radiator Tank Valve Tube Coolant Compatible CPU Intel® Pentium® Extreme Edition Series Intel® Pentium® D Processor Series Intel® Pentium® 4 Processor Series (LGA775) Intel® CoreTM 2 Duo Processor Series AMD AM2TM Series AMD AthlonTM FX Series AMD AthlonTM 64x2 Series AMD AthlonTM 64 Series 3. Feature Instruction 1. Super huge copper base and unique water path design. 2. Long-lived, quiet and powerful ceramic bearing pump. Place the waterblock on the top of Intel Pentium 4 LGA775 CPU( Figure b ) and adjust the appropriate installation direction ( Figure c ). ® ® Figure a Figure b Figure c 12 English 4-10-2 Secure Intel Pentium 4 LGA775 motherboard with attached spring screws. ® ® 4-11 AMD K8 Clip Installation 4-11-1 Align the AMD K8 Clip to three raised points on the CPU. 4-11-2 Push down the bar to surely secure. 4-12 AMD AM2 Clip Installation 4-12-1 Align the AMD K8 clip to the raised point on the CPU . 4-12-2 Push down the bar to surely secure. 13 English 4-13 Fasten 4-way Splitter Valve 4-13-1 Using the nylon tie to fasten 4-way splitter valve on trestle of the chassis. If there is no trestle available, try to find an applicable place to fasten it. 4 -14 MOSFET Air Cooling Fan Installation 4-14-1 Place MOSFET air cooling fan on the top of waterblock and make sure that four feet of the air cooling fan are secured on waterblock. 4-14-2 Plug the power cord of MOSFET air cooling fan to the socket on motherboard CPU fan. 4-14-3 Plug the power cord of MOSFET air cooling fan into fan 1 to 2 power cord. a :3-pin CPU fan socket b: 4-pin CPU fan socket (Intel® Pentium® 4 LGA775) 14 English 4-15 Pump Power Cord Installation 4-15-1 Prepare Pump Power Cord a : 6-pin connector b : female 2-pin connector c : male 2-pin connector d : 4-pin connector Connect the Power SW (female 2- pin c onnec tor) f rom the chassis's panel with the pump power cord male 2-pin connector. a : Power SW (female 2- pin connector) from the chassis's panel b : Pump power cord male 2-pin connector Connect the pump power SW cord female 2-pin connector with "+ PW-" jumper on the motherboard. A B D C 4-15-2 4-15-3 4-15-4 Connect the pump power cord 6-pin connector with the back of the tank, (as Figure a /b) Figure a Figure b 4-15-5 Connect 4 -pin power supply connector with the 4-pin pump cord connector. 15 English 4-16 Fan Speed Control Box and Power Cord Instruction Fan Speed Control Box Socket PCI Rear Fan Speed Control Box Connector Power Cord Fan Speed Control Box Connect the other side of power cord with fan 1 to 2 power cord Radiator Fan Speed Control Box Connector Socket 4-17 Fan Speed Control Box Installation Tool needed: Fan Speed Control Box , Fan Speed Control Box Connect Line. 4-17-1 Thread the radiator fan connector through the hole of PCI rear fan speed controller. 4-17-2 Plug the connector from the PCI rear fan speed controller into the fan speed control box. 16 English 4-17-3 Plug the radiator fan power cord into the fan speed control box. 4-17-4 To accomplish installation, plug the power cord of fan speed control box into the connector on the fan speed control box (as Figure a) and plug the other side of the power cord into the available 1 to 2 socket (as Figure b). Figure a Figure b 4-18 Heat Sink Installation 4-18-1 Heat sink( 8 pcs) can be pasted on the small chips on the motherboard or VGA card to lower the temperature. 17 English 5. Liquid Cooling System Installation and Test Before pouring liquid coolant into the tank to test the liquid cooling system, please remove the tank from the chassis to avoid damaging other components. Before turning on the power, please confirm that all the tube clips are fastened; leakage of liquid coolant due to improper installation may damage the system that is not covered by warranty. (as figure showen) Use only GIGABYTETM liquid coolant; any damage arising from using other liquid product is not covered by warranty. 5-1 Liquid Cooling System Installation and Test Tool needed: Coolant 5-1-1 Open the lid of the tank to pour in liquid coolant and close the lid. 18 English 5-1-2 Turn on the power until all liquid coolant drains into the tubes; the red light on the bottom of the PCB will blink and bleep; the system will turn off automatically within 4 seconds. (This is normal or initial refilling of liquid coolant since the tube and radiator are not full of liquid. ) 5-1-3 Open the lid of the tank again to refill the tank with liquid coolant and than close the lid. [. . . ] (as figure showen) Use only GIGABYTETM liquid coolant; any damage arising from using other liquid product is not covered by warranty. 5-1 Liquid Cooling System Installation and Test Tool needed: Coolant 5-1-1 Open the lid of the tank to pour in liquid coolant and close the lid. 18 English 5-1-2 Turn on the power until all liquid coolant drains into the tubes; the red light on the bottom of the PCB will blink and bleep; the system will turn off automatically within 4 seconds. (This is normal or initial refilling of liquid coolant since the tube and radiator are not full of liquid. ) 5-1-3 Open the lid of the tank again to refill the tank with liquid coolant and than close the lid. Turn on the power one more time and repeat this step until the water is no longer lower than the low water-level. Note: For the first time of pouring liquid coolant into the tank; the radiator should be lay down flat to facilitate exhaust air to ensure the liquid cooling system to function silently. Installing the radiator in accordance with the following step 5-2 ; make sure all the air bubble in the tube has been removed to ensure the performance of cooling. [. . . ]