User manual GIGABYTE 7NF-RZC

[. . . ] 7NF-RZ / 7NF-RZ-C AMD AthlonTM/AthlonTM XP/DuronTM Socket A Processor Motherboard User's Manual Rev. 1002 12ME-7NFRZ-1002 Copyright © 2004 GIGABYTE TECHNOLOGY CO. , LTD Copyright by GIGA-BYTE TECHNOLOGY CO. , LTD. No part of this manual may be reproduced or transmitted in any from without the expressed, written permission of GBT. Trademarks Third-party brands and names are the property of their respective owners. Notice Please do not remove any labels on motherboard, this may void the warranty of this motherboard. Due to rapid change in technology, some of the specifications might be out of date before publication of this booklet. [. . . ] You can use one of three methods: Auto Allows BIOS to automatically detect IDE devices during POST(default) None Select this if no IDE devices are used and the system will skip the automatic detection step and allow for faster system start up. Manual User can manually input the correct settings Access Mode Use this to set the access mode for the hard drive. The four options are: CHS/LBA/Large/Auto(default:Auto) Hard drive information should be labeled on the outside drive casing. Enter the appropriate option based on this information. Cylinder Number of cylinders Head Number of heads Precomp Write precomp Landing Zone Landing zone Sector Number of sectors If a hard disk has not been installed, select NONE and press <Enter>. - 21 - BIOS Setup English Drive A / Drive B The category identifies the types of floppy disk drive A or drive B that has been installed in the computer. None No floppy drive installed 360K, 5. 25" 5. 25 inch PC-type standard drive; 360K byte capacity. 1. 2M, 5. 25" 5. 25 inch AT-type high-density drive; 1. 2M byte capacity (3. 5 inch when 3 Mode is Enabled). 720K, 3. 5" 3. 5 inch double-sided drive; 720K byte capacity 1. 44M, 3. 5" 3. 5 inch double-sided drive; 1. 44M byte capacity. 2. 88M, 3. 5" 3. 5 inch double-sided drive; 2. 88M byte capacity. Floppy 3 Mode Support (for Japan Area) Disabled Drive A Drive B Both Normal Floppy Drive. (Default value) Drive A is 3 mode Floppy Drive. Drive A & B are 3 mode Floppy Drives. Halt on The category determines whether the computer will stop if an error is detected during power up. No Errors The system boot will not stop for any error that may be detected and you will be prompted. All Errors Whenever the BIOS detects a non-fatal error the system will be stopped. All, But Keyboard The system boot will not stop for a keyboard error; it will stop for all other errors. (Default value) All, But Diskette The system boot will not stop for a disk error; it will stop for all other errors. All, But Disk/Key The system boot will not stop for a keyboard or disk error; it will stop for all other errors. Memory The category is display-only which is determined by POST (Power On Self Test) of the BIOS. Base Memory The POST of the BIOS will determine the amount of base (or conventional) memory installed in the system. The value of the base memory is typically 512K for systems with 512K memory installed on the motherboard, or 640K for systems with 640K or more memory installed on the motherboard. Extended Memory The BIOS determines how much extended memory is present during the POST. This is the amount of memory located above 1 MB in the CPU's memory address map. Total Memory This item displays the memory size that used. 7NF-RZ Series Motherboard - 22 - Advanced BIOS Features CMOS Setup Utility-Copyright (C) 1984-2004 Award Software Advanced BIOS Features First Boot Device Second Boot Device Third Boot Device Boot Up Floppy Seek Password Check Init Display First [Floppy] [HDD-0] [CDROM] [Disabled] [Setup] [PCI] Item Help Menu Level Select Boot Device priority [Floppy] Boot from floppy [LS120] Boot from LS120 [HDD-0] Boot from First HDD [HDD-1] Boot from Second HDD : Move Enter: Select F5: Previous Values +/-/PU/PD: Value F6: Fail-Save Default F10: Save ESC: Exit F1: General Help F7: Optimized Defaults English First / Second / Third Boot Device Floppy LS120 HDD-0~3 SCSI CDROM ZIP USB-FDD USB-ZIP USB-CDROM USB-HDD LAN Disabled Select your boot device priority by Floppy. Select your boot device priority by LS120. Select your boot device priority by HDD-0~3. Select your boot device priority by SCSI. Select your boot device priority by CDROM. [. . . ] Support : http://www. giga-byte. com/TechSupport/ServiceCenter. htm Non-Tech. Support(Sales/Marketing) : http://ggts. gigabyte. com. tw/nontech. asp WEB address : http://www. giga-byte. com Germany G. B. T. TECHNOLOGY TRADING GMBH Address: Friedrich-Ebert-Damm 112 22047 Hamburg TEL: +49-40-2533040 (Sales) +49-1803-428468 (Tech. ) TEL: +49-40-25492343 (Sales) +49-1803-428329 (Tech. ) Tech. Support : http://de. giga-byte. com/TechSupport/ServiceCenter. htm Non-Tech. [. . . ]