User manual GIGABYTE GA-6IWFL

[. . . ] The author assumes no responsibility for any errors or omissions that may appear in this document nor does the author make a commitment to up date the information contained herein. Third-party brands and names are the property of their respective owners. Please do not remove any labels on motherboard, this may void the warranty of this motherboard. Due to rapid change in technology, some of the specifications might be out of date before pwblicution of this booklet. GA-6IWF Series Socket 370 Processor Motherboard USER'S MANUAL Socket 370 Processor Motherboard Rev. [. . . ] Set onboard I/O chip UART to Normal Mode. (Default Value) 38 BIOS Setup RxD, TxD Active Hi, Hi Hi, Lo Lo, Hi Lo, Lo Set RxD, TxD Active to Hi, Hi. (Default Value) Set RxD, TxD Active to Lo, Hi. Set RxD, TxD Active to Lo, Lo. IR Transmission Delay Enabled Disabled Enabled IR Transmission delay. (Default Value) Enabled IR Transmission delay. Use IR Pins IR-Rx2Tx2 RxD2, TxD2 Enable On Board LPT port and address is 378. (Default Value) Enable On Board LPT port and address is 278. Onboard Parallel port 378/IRQ7 278/IRQ5 3BC/IRQ7 Disabled Enable onboard LPT port and address is 378/IRQ7. (Default Value) Enable onboard LPT port and address is 278/IRQ5. Enable onboard LPT port and address is 3BC/IRQ7. Disable onboard LPT port. Onboard Parallel Mode Normal EPP ECP ECP/EPP Using Parallel port as Normal. Using Parallel port as Enhanced Parallel Port. Using Parallel port as Extended Capabilities Port. (Default Value) Using Parallel port as ECP & EPP mode. Parallel Port EPP Type EPP 1. 9 EPP 1. 7 EPP Version is 1. 9. (Default Value) EPP Version is 1. 7. 39 GA-6IWF Series Motherboard ECP Mode Use DMA 3 1 ECP Mode Use DMA 3 (Default Value) ECP Mode Use DMA 1 AC Back Function Memory Soft-Off Full-On System power on depends on the status before AC lost. (Default value) Always power on the system when AC back. Game Port Address Disabled 201 209 Disabled this function. Set Game Port Address to 201. (Default Value) Set Game Port Address to 209. Midi Port Address Disabled 330 300 Disabled this function. Set Game Port Address to 330. (Default Value) Set Game Port Address to 300. Midi Port IRQ 5 10 Set 5 for Midi Port IRQ. (Default Value) 40 BIOS Setup Power Management Setup CMOS Setup Utility-Copyright (C) 1984-2001 Award Software Power Management Setup ACPI Suspend Type Power Management Video Off Method Video Off In Suspend Suspend Type MODEM Use IRQ Suspend Mode HDD Power Down Soft-Off by PWR-BTTN PME Event Wake Up ModemRingOn/WakeOnLan USB Device Wake-Up From S3 CPU Thermal-Throttling Resume by Alarm Date(of Month) Alarm Time(hh:mm:ss) Alarm ** Reload Global Timer Events ** Primary IDE 0 Primary IDE 1 Secondary IDE 0 Secondary IDE 1 FDD, COM, LPT Port PCI PIRQ[A-D]# Disabled Disabled Disabled Disabled Disabled Disabled S1(POS) User Define DPMS Yes Stop Grant NA Disabled Disabled Instant-off Disabled Enabled Disabled 50% Disabled Everyday 0 0 0 Item Help Menu Level : Move Enter:Select +/-/PU/PD:Value F10:Save ESC:Exit F1:General Help F5:Previous Values F6:Fail-Safe Defaults F7:Optimized Defaults Figure 6: Power Management Setup 41 GA-6IWF Series Motherboard ACPI Suspend Type S1(POS) S3(STR) Set ACPI suspend type is S1. (Default Value) Set ACPI suspend type is S3. Power Management User Define Min Saving Man Saving For configuring our own power management features. Disable Green function. Video off Method V/H SYNC+Blank Blank Screen DPMS BIOS will turn off V/H-SYNC when gets into Green mode for Green monitor power saving. BIOS will only black monitor when gets into Green mode. BIOS will use DPMS Standard to control VGA card. (The Green type VGA card will turn off V/H-SYNC automatically. ) (Default value) Video Off In Suspend Yes No Set Suspend type is stop grant. (Default value) SuspendSet Suspend type is Power on Suspend. Suspend Type Stop Grant PwrOn Suspend Set Suspend type is stop grant. [. . . ] [Enter] to continue Or [Esc] to cancel? (4) The BIOS flash completed. Please press [ESC] to exit Flash Utility. EXIT?[Enter] to continue Or [Esc] to cancel? 74 Appendix STEP 6: Load BIOS defaults. Normally the system redetects all devices after BIOS has been upgraded. [. . . ]