User manual GIGABYTE GA-6WMM

[. . . ] Operation is subjected to the following two conditions 1) this device may not cause harmful interference and 2) this device must accept any interference received, including interference that may cause undesired operation. Declaration of Conformity We, Manufacturer/Importer (full address) G. B. T. Technology Träding GMbH Ausschlager Weg 41, 1F, 20537 Hamburg, Germany declare that the product ( description of the apparatus, system, installation to which it refers) Mother Board GA-6WMM is in conformity with (reference to the specification under which conformity is declared) in accordance with 89/336 EEC-EMC Directive EN 55011 Limits and methods of measurement of radio disturbance characteristics of industrial, scientific and medical (ISM high frequency equipment Limits and methods of measurement of radio disturbance characteristics of broadcast receivers and associated equipment Limits and methods of measurement of radio disturbance characteristics of household electrical appliances, portable tools and similar electrical apparatus Limits and methods of measurement of radio disturbance characteristics of fluorescent lamps and luminaries Immunity from radio interference of broadcast receivers and associated equipment Limits and methods of measurement of radio disturbance characteristics of information technology equipment Cabled distribution systems; Equipment for receiving and/or distribution from sound and television signals EN 61000-3-2* EN60555-2 Disturbances in supply systems caused by household appliances and similar electrical equipment "Harmonics" EN55013 EN61000-3-3* EN60555-3 Disturbances in supply systems caused by household appliances and similar electrical equipment "Voltage fluctuations" EN 55014 EN 50081-1 Generic emission standard Part 1: Residual, commercial and light industry Generic immunity standard Part 1: Residual, commercial and light industry Generic emission standard Part 2: Industrial environment EN 50082-1 EN 55015 EN 55081-2 EN 55020 EN 55082-2 Generic immunity standard Part 2: Industrial environment EN 55022 ENV 55104 Immunity requirements for household appliances tools and similar apparatus DIN VDE 0855 part 10 part 12 EN 50091- 2 EMC requirements for uninterruptible power systems (UPS) CE marking (EC conformity marking) The manufacturer also declares the conformity of above mentioned product with the actual required safety standards in accordance with LVD 73/23 EEC EN 60065 Safety requirements for mains operated electronic and related apparatus for household and similar general use Safety of household and similar electrical appliances EN 60950 Safety for information technology equipment including electrical business equipment EN 60335 EN 50091-1 General and Safety requirements for uninterruptible power systems (UPS) Manufacturer/Importer Signature : (Stamp) Rex Lin Rex Lin Date : Aug. 05, 1999 Name : 6WMM Series Pentium® II / III / Celeron TM Processor Motherboard USER'S MANUAL Pentium® II/III/Celeron TM Processor MAINBOARD REV. 1. 3 Third Edition R-13-03-091123 How This Manual is Organized This manual is divided into the following sections: 1) Revision History 2) Item Checklist 3) Features 4) Hardware Setup 5) Performance & Block Diagram 6) Suspend to RAM 7) BIOS Setup 8) Appendix Manual revision information Product item list Product information & specification Instructions on setting up the motherboard Product performance & block diagram Instructions STR installation Instructions on setting up the BIOS software General reference Table Of Content Revision History Item Checklist Summary of Features 6WMM Series Motherboard Layout Page Index for CPU Speed Setup / Connectors / Panel and Jumper Definition Performance List Block Diagram Suspend to RAM Installation Memory Installation Page Index for BIOS Setup Appendix P. 1 P. 2 P. 3 P. 5 P. 6 P. 29 P. 30 P. 31 P. 37 P. 38 P. 74 6WMM Series Motherboard Revision History Revision 1. 3 1. 3 1. 3 Revision Note Initial release of the 6WMM series motherboard user's manual. Second release of the 6WMM series motherboard user's manual Third release of the 6WMM series motherboard user's manual Date Sep. 1999 Oct. [. . . ] Definition 1-2 close Clear CMOS 2-3 close Normal (Default) JP7 : Case Open 1 Pin No. Definition 1 Signal 2 GND 23 Panel and Jumper Definition JP2 : STR LED Connector STR LED Connector External. + RAM Indicator LED1 1 JP1 : Top Block Lock 1 Pin No. Definition Open TBL Lock Close UN Lock 24 6WMM Series Motherboard JP5 : Timeout Reboot Function 1 Pin No. Definition Open Timeout reboot Close No Reboot on timeout J1 : Buzzer Enable 1 Pin No. Definition Open Internal Buzzer Disable Close Internal Buzzer Enable (Default) 25 Panel and Jumper Definition JP32 : Onboard Sound Function Selection 1 Definition Disable 1-2 close Onboard sound Enable 2-3 close Onboard sound (Default) Pin No. J21 : AMR Selection 1 Pin No. Definition 1-2close Secondary AMR 2-3close Disable CODEC 26 6WMM Series Motherboard JP11 : STR Enable 1 Pin No. Open Close Definition STR Disabled (Default) STR Enabled JP18 : Normal / Safe mode / Recovery 1 Pin No. Definition 1-2close Normal(Default) 2-3close Safe mode 1-2-3open Recovery 27 Panel and Jumper Definition BAT1 : Battery + + Danger of explosion if battery is incorrectly replaced. + Replace only with the same or equivalent type recommended by the manufacturer. + Dispose of used batteries according to the manufacturer's instructions. 28 6WMM Series Motherboard Performance List The following performance data list is the testing results of some popular benchmark testing programs. These data are just referred by users, and there is no responsibility for different testing data values gotten by users. (The different Hardware & Software configuration will result in different benchmark testing results. ) · CPU · DRAM · CACHE SIZE · DISPLAY · STORAGE · O. S. · DRIVER Pentium® III 500MHz processor (128x1)MB SDRAM (Winbond 902WB 986408BH-8H) 512 KB included in CPU Onboard Intel Corporation 810 Graphics and Memory Controller Hub (4MB SDRAM) Onboard IDE (IBM DJNA-371800) Windows NTTM SPK5 4. 0 Display Driver at 1024 x 768 x 16bit colors x 75Hz. Processor Winbench99 CPU mark99 FPU Winmark 99 Business Disk Winmark 99 Hi-End Disk Winmark 99 Business Graphics Winmark 99 Hi-End Graphics Winmark 99 Intel Pentium® III 500MHz(100x5) 38. 2 2560 3650 6370 149 344 30 24. 7 Winstone99 Business Winstone99 Hi-End Winstone99 29 Block Diagram Block Diagram INTEL Slot 1 Processor Display 66/100/133 MHz Host Bus 66/100/133MHz 66/100/133 MHz Display Cache SDRAM SDRAM GMCH 82810E Hub Interface 3. 3V SDRAM 100 MHz ICS 14. 318/33/48/66 MHz PCI Bus 33MHz 9248-96 4 PCI ICH ATA66 IDE Channels 82801AA AC'97 Link YMF 2 USB Ports FWH 744 COM Ports 3 COM AC'97 Winbond W83627 Game Port LPT Ports IR Floppy PS/2 30 6WMM Series Motherboard Suspend to RAM Installation A. 1 Introduce STR function: Suspend-to-RAM (STR) is a Windows 98 ACPI sleep mode function. When recovering from STR (S3) sleep mode, the system is able, in just a few seconds, to retrieve the last "state" of the system before it went to sleep and recover to that state. The "state" is stored in memory (RAM) before the system goes to sleep. During STR sleep mode, your system uses only enough energy to maintain critical information and system functions, primarily the system state and the ability to recognize various "wake up" triggers or signals, respectively. A. 2 STR function Installation Please use the following steps to complete the STR function installation. Step-By-Step Setup Step 1: To utilize the STR function, the system must be in Windows 98 ACPI mode. Putting Windows 98 into ACPI mode is fairly easy. Insert the Windows 98 CD into your CD-ROM drive, select Start, and then Run. Type (without quotes) "D:\setup /p j" in the window provided. After setup completes, remove the CD, and reboot your system (This manual assumes that your CD-ROM device drive letter is D:). 31 Suspend to RAM installation Step 2: (If you want to use STR Function, please set jumper JP11 (Closed. ) 1 Pin No. [. . . ] Use the "Wake On LAN" function. 35 Suspend to RAM installation A. 5 Notices : 1. In order for STR to function properly, several hardware and software requirements must be satisfied: A. Your ATX power supply must comply with the ATX 2. 01 specification (provide more than 720 mA 5V Stand-By current). Jumper JP2 is provided to connect to the STR LED in your system chassis. [. . . ]