User manual GIGABYTE GA-7TCSV1

[. . . ] GA-7TCSV-RH Dual Xeon Processor Motherboard USER'S MANUAL XeonTM Processor Motherboard Rev. 1001 * The WEEE marking on the product indicates this product must not be disposed of with user's other household waste and must be handed over to a designated collection point for the recycling of waste electrical and electronic equipment!!The WEEE marking applies only in European Union's member states. * GA-7TCSV-RH Motherboard English Table of Contents Item Checklist . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Chapter 1Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] Dispose of used batteries according to the manufacturer's instructions. 22 ) CLR_CMOS1 (Clear CMOS Function) You may clear the CMOS data to its default values by this jumper. Default value doesn't include the "Shunter" to prevent from improper use this jumper. To clear CMOS, temporarily short 2-3 pin. 1 1 1-2 close: Normal operation (Default setting) 2-3 close: Clear CMOS 22 GA-7TCSV-RH Motherboard English 23 ) JP_REC1 ( BIOS Recovery jumper) 1 1 1-2 close: Normal operation. (Default setting) 2-3 close: Enable BIOS Recovery function. 24 ) PASS_DIS1 (Skip Supervisor password jumper) 1 1 1-2 Close: Normal operation. (Default setting) 2-3 Close: Clear Supervisor Password in BIOS setup menu. 23 GA-7TCSV-RH Motherboard English 2. 5. Block Diagram VRD 11. 1 SPD0 VRD 11. 1 SPD1 DDR3 DDR3 DDR3 CPU0 Nehalem-EP LGA 1366 CPU1 Nehalem-EP LGA 1366 QPI DDR3 DDR3 DDR3 Super I/O ITE IT8720F INTEL 82567LM GbE INTEL 82574L GbE RJ45 & USB 2. 0 RJ45 & USB 2. 0 COMA COMB PCI-E x16 Slot PCI-E x8 Slot PCI-E x8 Slot PCIE Gen2 PCIE x4 Gen2 PCIE x4 Gen2 INTEL TYLERSBURG-24D IOH LPC QPI PCI-E x8 Slot PCIE x4 Gen1 INTEL ICH10R GLC/LCI PCI PCIE x1 PCI32/33MHz USB X1*2 XGI Z9s SATA2 x 6 USB X1*2 VGA Connector USB X1*2 Front USB 24 GA-7TCSV-RH Motherboard Chapter 3 BIOS Setup BIOS (Basic Input and Output System) includes a CMOS SETUP utility which allows user to configure required settings or to activate certain system features. The CMOS SETUP saves the configuration in the CMOS SRAM of the motherboard. When the power is turned off, the battery on the motherboard supplies the necessary power to the CMOS SRAM. ENTERINGSETUP When the power is turned on, press the <F2> button during the BIOS POST (Power-On Self Test) will take you to the CMOS SETUP screen. You can enter the BIOS setup screen by pressing "Ctrl + F1". CONTROLKEYS <> <> < < > > Move to previous item Move to next item Move to the item in the left hand Move to the item in the right hand Main Menu - Quit and not save changes into CMOS Status Page Setup Menu and Option Page Setup Menu - Exit current page and return to Main Menu <+/PgUp> Increase the numeric value or make changes <-/PgDn> <F1> <F2> <F3> <F4> <F6> <F7> <F8> <F9> <F10> Decrease the numeric value or make changes General help, only for Status Page Setup Menu and Option Page Setup Menu Reserved Reserved Reserved Reserved Reserved Reserved Load the Optimized Defaults Save all the CMOS changes, only for Main Menu <Esc> 25 BIOS Setup GETTINGHELP Main Menu The on-line description of the highlighted setup function is displayed at the bottom of the screen. Status Page Setup Menu / Option Page Setup Menu Press F1 to pop up a small help window that describes the appropriate keys to use and the possible selections for the highlighted item. To exit the Help Window press <Esc>. Select the Load Setup Defaults item in the BIOS Exit Setup menu when somehow the system is not stable as usual. This action makes the system reset to the default settings for stability. Main This setup page includes all the items in standard compatible BIOS. Advanced This setup page includes all the items of Phoenix BIOS special enhanced features. (ex: Auto detect fan and temperature status, automatically configure hard disk parameters. ) Security Change, set, or disable password. It allows you to limit access the system and setup. Server Server additional features enabled/disabled setup menus. Boot This setup page include all the items of first boot function features. Exit There are five optionsin this selection: Exit Saving Changes, Exit Discarding Changes, Load Optimal Defaults, Load Failsafe Defaults, and Discard Changes. 26 GA-7TCSV-RH Motherboard Main Once you enter Phoenix BIOS Setup Utility, the Main Menu (Figure 1) will appear on the screen. Use arrow keys to select among the items and press <Enter> to accept or enter the sub-menu. Figure 1: Main System Time The time is calculated based on the 24-hour military time clock. Set the System Time (HH:MM:SS) System Time Set the System Date. Note that the "Day" automatically changed after you set the date. (Weekend: DD: MM: YY) (YY: 1099~2099) 27 BIOS Setup SATA Port 1/2/3/4/5/6 The category identifies the types of Serial SATA hard disk from drive 1 to 6 that has been installed in the computer. System will automatically detect HDD type. Note that the specifications of your drive must match with the drive table. The hard disk will not work properly if you enter improper information for this category. Hard drive information should be labled on the outside device casing. [. . . ] Serial Port A Serial Port B Disabled Use Serial Port A as the COM port address. Use Serial Port B as the COM port address. (Default setting) Baud Rate This option allows user to set the specified baud rate. Options 300, 1200, 2400, 9600, 19. 2K, 38. 4K, 57. 6K, 115. 2K. Console Type This option allows user to select the specified terminal type. [. . . ]