User manual GIGABYTE GA-7VT600

[. . . ] When you installing AGP card, please make sure the following notice is fully understood and practiced. If your AGP card has "AGP 4X/8X(1. 5V) notch"(show below), please make sure your AGP card is AGP 4X/8X(1. 5V). AGP 4X/8X notch Caution: AGP 2X(3. 3V) card is not supported by VIA® KT600. You might experience system unable to boot up normally. Please insert an AGP 4X/8X(1. 5V) card Example 1: Diamond Vipper V770 golden finger is compatible with 2X/4X mode AGP slot. [. . . ] Enable onboard Serial port 1 and address is 3F8, Using IRQ4. (Default value) Enable onboard Serial port 1 and address is 2F8, Using IRQ3. Enable onboard Serial port 1 and address is 3E8, Using IRQ4. Enable onboard Serial port 1 and address is 2E8, Using IRQ3. Disable onboard Serial port 1. FOnboard Serial Port 2 8Auto 83F8/IRQ4 82F8/IRQ3 83E8/IRQ4 82E8/IRQ3 8Disabled BIOS will automatically setup the port 2 address. Enable onboard Serial port 2 and address is 3F8, Using IRQ4. Enable onboard Serial port 2 and address is 2F8, Using IRQ3. (Default Value) Enable onboard Serial port 2 and address is 3E8, Using IRQ4. Enable onboard Serial port 2 and address is 2E8, Using IRQ3. Disable onboard Serial port 2. FOnBoard Parallel port MThis feature allows you to select from a given set of parameters if the parallel port uses the onboard I/O controller. 8378/IRQ7 8278/IRQ5 83BC/IRQ7 8Disabled Enable onboard LPT port and address is 378, Using IRQ7. (Default Value) Enable onboard LPT port and address is 278, Using IRQ5. Enable onboard LPT port and address is 3BC, Using IRQ7. Disable onboard parallel port. " * " FOR GA-7VT600-L Only. - 41 - BIOS Setup . English FParallel Port Mode MThis feature allows you to connect with an advanced print via the port mode it supports. 8SPP 8EPP 8ECP 8ECP+EPP Using Parallel port as Standard Parallel Port using IRQ7. (Default Value) Using Parallel port as Enhanced Parallel Port IRQ5. Using Parallel port as Extended Capabilities Port using IRQ7. Using Parallel port as ECP & EPP mode. FGame Port Address 8Disabled 8201 8209 Disabled this function. (Default Value) Set Game Port Address to 209. FMidi Port Address 8Disabled 8300 8330 Disabled this function. Set Midi Port Address to 330. (Default Value) FMidi Port IRQ 85 810 Set 5 for Midi Port IRQ. Set 10 for Midi Port IRQ. (Default value) GA-7VT600(-L) Motherboard - 42 - English Power Management Setup CMOS Setup Utility-Copyright (C) 1984-2003 Award Software Power Management Setup ACPI Suspend Type øUSB Device Wake-Up From S3 Power LED in S1 state Soft-Off by PWRBTN AC Back Function Keyboard Power On Mouse Power On PME Event Wake Up ModemRingOn/WakeOnLAN Resume by Alarm ø Date(of Month) Alarm ø Time(hh:mm:ss) Alarm [S1(POS)] Disabled [Blinking] [Instant-off] [Soft-Off] [Disabled] [Disabled] [Enabled] [Enabled] [Disabled] Everyday 0: 0: 0 Item Help Menu Levelu higf: Move Enter:Select +/-/PU/PD:Value F10:Save ESC:Exit F1:General Help F5:Previous Values F6:Fail-Safe Defaults F7:Optimized Defaults Figure 5: Power Management Setup - 43 - BIOS Setup English FACPI Suspend Type 8S1(POS) 8S3(STR) Set suspend type to Power On Suspend under ACPI OS(Power On Suspend). (Default value) Set suspend type to Suspend To RAM under ACPI OS (Suspend To RAM). FUSB Device Wakeup From S3(When ACPI Suspend Type is set [S3(STR)]) USB device wakeup From S3 can be set when ACPI standby state set to S3/STR. 8Enabled 8Disabled USB Device can wakeup system from S3. USB Device can't wakeup system from S3. (Default value) FPower LED in S1 state 8Blinking 8Dual/Off In standby mode(S1), power LED will blink. If use single color LED, power LED will turn off. [. . . ] *Except for beep code 8, these codes are always fatal. 1 beep Refresh failure 2 beeps Parity error 3 beeps Base 64K memory failure 4 beeps Timer not operational 5 beeps Processor error 6 beeps 8042 - gate A20 failure 7 beeps Processor exception interrupt error 8 beeps Display memory read/write failure 9 beeps ROM checksum error 10 beeps CMOS shutdown register read/write error 11 beeps Cache memory bad g AWARD BIOS Beep Codes 1 short: System boots successfully 2 short: CMOS setting error 1 long 1 short: DRAM or M/B error 1 long 2 short: Monitor or display card error 1 long 3 short: Keyboard error 1 long 9 short: BIOS ROM error Continuous long beeps: DRAM error Continuous short beeps: Power error English - 79 - Appendix English Troubleshooting If you encounter any trouble during boot up, please follow the troubleshooting procedures . START Turn off the power and unplug the AC power cable, then remove all of the add-on cards and cables from motherboard. Please make sure motherboard & chassis are not short ? Yes Please isolate the short pin. No Failure has been excluded. Please make sure all jumper settings (such as CPU system bus speed, frequency ratio, voltage and etc. ) are set properly. No Make sure the jumper setting are correct. Yes Failure has been excluded. No Plug the CPU cooling fan power in the CPU fan connector. Plug in the AC power connector. Check if the CPU cooling fan attached to CPU properly. [. . . ]