User manual GIGABYTE GA-7ZX-1

[. . . ] FCC Compliance Statement: This equipment has been tested and found to comply with limits for a Class B digital device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in residential installations. This equipment generates, uses, and can radiate radio frequency energy, and if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. [. . . ] The program that allows users to modify the basic system configuration. This type of information is stored in battery-backed CMOS RAM so that it retains the Setup information when the power is turned off. ENTERING SETUP Power ON the computer and press <Del> immediately will allow you to enter Setup. If the message disappears before you respond and you still wish to enter Setup, restart the system to try again by turning it OFF then ON or pressing the "RESET" bottom on the system case. You may also restart by simultaneously press <Ctrl> - <Alt>- <Del> keys. CONTROL KEYS <> <> <> <> <Esc> Move to previous item Move to next item Move to the item in the left hand Move to the item in the right hand Main Menu - Quit and not save changes into CMOS Status Page Setup Menu and Option Page Setup Menu - Exit current page and return to Main Menu Increase the numeric value or make changes Decrease the numeric value or make changes General help, only for Status Page Setup Menu and Option Page Setup Menu Reserved Reserved Reserved Restore the previous CMOS value from CMOS, only for Option Page Setup Menu Load the default CMOS value from BIOS default table, only for Option Page Setup Menu Load the Setup Defaults Reserved Reserved Save all the CMOS changes, only for Main Menu <+/PgUp> <-/PgDn> <F1> <F2> <F3> <F4> <F5> <F6> <F7> <F8> <F9> <F10> 48 7ZX Series Motherboard GETTING HELP Main Menu The on-line description of the highlighted setup function is displayed at the bottom of the screen. Status Page Setup Menu / Option Page Setup Menu Press F1 to pop up a small help window that describes the appropriate keys to use and the possible selections for the highlighted item. To exit the Help Window press <Esc>. The Main Menu Once you enter AMI BIOS CMOS Setup Utility, the Main Menu (Figure 1) will appear on the screen. The Main Menu allows you to select from nine setup functions and two exit choices. Use arrow keys to select among the items and press <Enter> to accept or enter the sub-menu. AMIBIOS SIMPLE SETUP UTILITY-VERSION 1. 24b ( C ) 1999 American Megatrends, Inc. All Rights Reserved STANDARD CMOS SETUP BIOS FEATURES SETUP CHIPSET FEATURES SETUP POWER MANAGEMENT SETUP PNP/PCI CONFIGURATION LOAD BIOS DEFAULTS LOAD SETUP DEFAULTS INTEGRATED PERIPHERALS HARDWARE MONITOR & MISC SETUP SUPERVISOR PASSWORD USER PASSWORD IDE HDD AUTO DETECTION SAVE & EXIT SETUP EXIT WITHOUT SAVING ESC : Quit (Shift) F2 : Change Color F5 : Old Values : Select Item F6 : Load BIOS Defaults F7: Load Setup Defaults F10: Save & Exit Time, Date, Hard Disk Type, . . . Figure 1: Main Menu · Standard CMOS Setup This setup page includes all the items in standard compatible BIOS. · BIOS Features Setup This setup page includes all the items of AMI special enhanced features. 49 BIOS Setup · Chipset Features Setup This setup page includes all the items of chipset special features. · Power Management Setup This setup page includes all the items of Green function features. · PNP/PCI Configurations This setup page includes all the configurations of PCI & PnP ISA resources. · Load BIOS Defaults Bios Defaults indicates the value of the system parameter which the system would be in the safe configuration. · Load Setup Defaults Setup Defaults indicates the value of the system parameter which the system would be in the most appropriate configuration. · Integrated Peripherals This setup page includes all onboard peripherals. · Hardware Monitor & MISC Setup This setup page is auto detect fan and temperature status. · Supervisor password Change, set, or disable password. It allows you to limit access to the system and Setup, or just to Setup. · User password Change, set, or disable password. It allows you to limit access to the system. · IDE HDD auto detection Automatically configure hard disk parameters. · Save & Exit Setup Save CMOS value settings to CMOS and exit setup. · Exit Without Saving Abandon all CMOS value changes and exit setup. 50 7ZX Series Motherboard Standard CMOS Setup The items in Standard CMOS Features Menu (Figure 2) are divided into 9 categories. Each category includes no, one or more than one setup items. Use the arrows to highlight the item and then use the <PgUp> or <PgDn> keys to select the value you want in each item. AMIBIOS SETUP ­ STANDARD CMOS SETUP ( C ) 1999 American Megatrends, Inc. All Rights Reserved Date (mm/dd/yyyy) : Fri Mar 9, 2001 Time (hh/mm/ss) : 10:36:24 TYPE SIZE CYLS Pri Master Pri Slave Sec Master Sec Slave : : : : Auto Auto Auto Auto Base Memory : 640 Kb Other Memory: 384 Kb Extended Memory: 127Mb Total Memory: 128Mb ESC : Exit : Select Item PU/PD/+/­ : Modify (Shift)F2 : Color HEAD PRECOMP LANDZ SECTOR MODE Floppy Drive A: 1. 44 MB 3 ½ Floppy Drive B: Not Installed Boot Sector Virus Protection : Disabled Month: Jan ­ Dec Day: 01 ­ 31 Year : 1990­ 2099 Figure 2: Standard CMOS Setup · Date The date format is <Week> <Month> <Day>, <Year>. Week Month Day Year The week, from Sun to Sat, determined by the BIOS and is display-only The month, Jan. The day, from 1 to 31 (or the maximum allowed in the month) The year, from 1990 through 2099 51 BIOS Setup · Time The times format in <hour> <minute> <second>. The time is calculated base on the 24-hour military-time clock. is 13:00:00. · Primary Master, Slave / Secondary Master, Slave The category identifies the types of hard disk from drive C to F that has been installed in the computer. There are two types: auto type, and user definable type. User type is user-definable; Auto type which will automatically detect HDD type. Note that the specifications of your drive must match with the drive table. The hard disk will not work properly if you enter improper information for this category. [. . . ] Check out supported motherboard and Flash ROM: In the very beginning, there is "About this program" icon shown in dialog box. It can help you check out which kind of motherboard and which brand of Flash ROM are supported. In method I, if it shows two or more motherboard's model names to be selected, please make sure your motherboard's model name again. Sellecting name will cause the system unbooted. [. . . ]