User manual GIGABYTE GA-8I915P DUAL GRAPHIC

[. . . ] GA-8I915P Dual Graphic Intel® Pentium® 4 LGA775 Processor Motherboard User's Manual Rev. 1002 12ME-8I915PDG-1002 Motherboard GA-8I915P Dual Graphic Motherboard GA-8I915P Dual Graphic Jan. 13, 2005 Copyright © 2004 GIGA-BYTE TECHNOLOGY CO. , LTD. The trademarks mentioned in the manual are legally registered to their respective companies. Notice The written content provided with this product is the property of Gigabyte. [. . . ] (Default value) Set PCI Express frequency from 100MHz to 130MHz. Memory Frequency For Wrong frequency may make system can't boot, clear CMOS to overcome wrong frequency issue. for FSB(Front Side Bus) frequency=533MHz, 2. 5 Memory Frequency = Host clock X 2. 5. Auto Set Memory frequency by DRAM SPD data. (Default value) for FSB(Front Side Bus) frequency=800MHz, 1. 66 Memory Frequency = Host clock X 1. 66. 2. 66 Memory Frequency = Host clock X 2. 66. 3. 00 (Note) Memory Frequency = Host clock X 3. Auto Set Memory frequency by DRAM SPD data. (Default value) Memory Frequency (Mhz) The values depend on "Memory Frequency For" item. DIMM OverVoltage Control Please note that by overclocking your system through the increase of the DIMM voltage, damage to the memory may occur. Normal Set DIMM OverVoltage Control to Normal. (Default value) +0. 1V Set DIMM OverVoltage Control to +0. 1V. +0. 2V Set DIMM OverVoltage Control to +0. 2V. (Note) To use a DDRII 600 memory module on the motherboard, you must install an 800MHz FSB processor and set Memory Frequency For to 3. 00. - 47 BIOS Setup English +0. 3V Set DIMM OverVoltage Control to +0. 3V. Incorrect using it may cause your system broken. For power End-User use only! PCI-E OverVoltage Control Normal +0. 1V +0. 2V +0. 3V Normal +0. 1V +0. 2V +0. 3V Set PCI-E OverVoltage Control to Normal. (Default value) Set PCI-E OverVoltage Control to +0. 1V. (Default value) Set FSB OverVoltage Control to +0. 1V. Set FSB OverVoltage Control to +0. 3V. FSB OverVoltage Control CPU Voltage Control Supports adjustable CPU Vcore from 0. 8375V to 1. 6000V. (Default value: Normal) Warning: CPU may be damaged or reduce CPU life-cycle when CPU is over-voltage. Normal CPU Vcore Display your CPU Vcore Voltage. 2-8 Load Fail-Safe Defaults CMOS Setup Utility-Copyright (C) 1984-2004 Award Software Standard CMOS Features Load Fail-Safe Defaults Advanced BIOS Features Load Optimized Defaults Integrated Peripherals Set Supervisor Password Power Management Setup Set User Password Load Fail-Safe DefaultsSave & Exit Setup (Y/N)?N PnP/PCI Configurations PC Health Status Exit Without Saving MB Intelligent Tweaker(M. I. T. ) ESC: Quit F8: Dual BIOS/Q-Flash : Select Item F10: Save & Exit Setup Load Fail-Safe Defaults Fail-Safe defaults contain the most appropriate values of the system parameters that allow minimum system performance. GA-8I915P Dual Graphic Motherboard - 48 - 2-9 Load Optimized Defaults CMOS Setup Utility-Copyright (C) 1984-2004 Award Software Standard CMOS Features Load Fail-Safe Defaults Advanced BIOS Features Load Optimized Defaults Integrated Peripherals Set Supervisor Password Power Management Setup Set User Password Load Optimized Defaults (Y/N)?Exit Setup PnP/PCI Configurations Save & N PC Health Status Exit Without Saving MB Intelligent Tweaker(M. I. T. ) ESC: Quit F8: Dual BIOS/Q-Flash : Select Item F10: Save & Exit Setup Load Optimized Defaults English Selecting this field loads the factory defaults for BIOS and Chipset Features which the system automatically detects. 2-10 Set Supervisor/User Password CMOS Setup Utility-Copyright (C) 1984-2004 Award Software Standard CMOS Features Advanced BIOS Features Integrated Peripherals Power Management Setup PnP/PCI Configurations Enter Password: PC Health Status MB Intelligent Tweaker(M. I. T. ) ESC: Quit F8: Dual BIOS/Q-Flash Load Fail-Safe Defaults Load Optimized Defaults Set Supervisor Password Set User Password Save & Exit Setup Exit Without Saving : Select Item F10: Save & Exit Setup Change/Set/Disable Password Selecting this field loads the factory defaults for BIOS and Chipset Features which the system automatically detects. When you select this function, the following message will appear at the center of the screen to assist you in creating a password. Type the password, up to eight characters, and press <Enter>. You will be asked to confirm the password. [. . . ] TEL: +1 (626) 854-9338 FAX: +1 (626) 854-9339 Tech. Support : http://www. giga-byte. com/TechSupport/ServiceCenter. htm Non-Tech. Support(Sales/Marketing) : http://ggts. gigabyte. com. tw/nontech. asp WEB address : http://www. giga-byte. com Germany G. B. T. TECHNOLOGY TRADING GMBH Address: Friedrich-Ebert-Damm 112 22047 Hamburg TEL: +49-40-2533040 (Sales) +49-1803-428468 (Tech. ) FAX: +49-40-25492343 (Sales) +49-1803-428329 (Tech. ) Tech. [. . . ]