User manual GIGABYTE GA-8IE2004P-L

[. . . ] When you installing AGP card, please make sure the follow ing notice is fully understood and practiced. If your AGP card has "AGP 4X notch"(show below), please make sure your AGP card is AGP 4X (1. 5V). Caution: AGP 2X(3. 3V) card is not supported by Intel® 845 (E/G)/ Intel® 850(E) . You might experience system unable to boot up normally. Please insert an AGP 4X(1. 5V) card Example 1: Diamond Vipper V770 golden finger is compatible with 2X/4X mode AGP slot. [. . . ] (Default value) Set ACPI Suspend Type to S3/STR (Suspend To RAM). C Power LED in S1 State 8Blinking 8Dual/Off In standby mode(S1), power LED will blink. If use single color LED, power LED will turn off. If use dual color LED, power LED will turn to another color. FSoft-off by PWR-BTTN 8Instant-off 8Delay 4 Sec. Press power button then Power off instantly. (Default value) Press power button 4 sec to Power off. Enter suspend if button is pressed less than 4 sec. FPME Event Wake up MWhen set at Enabled, any PCI-PM event awakes the system from a PCI-PM controlled state. MThis feature requires an ATX power supply that provides at least 1A on the +5VSB lead. 8Disabled 8Enabled Disabled PME Event Wake up function. (Default Value) FModem Ring On M An incoming call via modem awakes the system from its soft-off mode. 8Disabled 8Enabled Disabled Modem Ring On function. (Default Value) FResume by Alarm You can set "Resume by Alarm" item to enabled and key in Data/time to power on system. 8Disabled 8Enabled Disable this function. (Default Value) Enable alarm function to POWER ON system. GA-8IE2004P(-L) Motherboard - 40 - If RTC Alarm Lead To Power On is Enabled. Date ( of Month) Alarm : Time ( hh: mm: ss) Alarm : Everyday, 1~31 (0~23) : (0~59) : (0~59) English FPower On By Mouse 8Disabled 8Mouse Click Disabled this function. (Default value) Set mouse double click to power on system. F Power On By Keyboard This feature allows you to set the method for powering-on the system. The option " Password"allows you to set up to 5 alphanumeric characters to power-on the system. The option " Keyboard 98"allows you to use the standard keyboard 98 to power on the system. 8Password 8Disabled 8Keyboard 98 Enter from 1 to 5 characters to set the Keyboard Power On Password. (Default value) If your keyboard have " POWER Key"button, you can press the key to power on your system. FKB Power ON Password 8Enter Input password (from 1 to 5 characters) and press Enter to set the Key board Power On Password. . FAC Back Function 8Memory 8Soft-Off 8Full-On System power on depends on the status before AC lost. (Default value) Always power on the system when AC back. - 41 - BIOS Setup English PnP/PCI Configurations CMOS Setup Utility-Copyright (C) 1984-2003 Award Software PnP/PCI Configurations PCI1/PCI5 IRQ Assignment PCI2 IRQ Assignment PCI3 IRQ Assignment PCI4 IRQ Assignment [Auto] [Auto] [Auto] [Auto] Item Help Menu Level higf: Move Enter:Select +/-/PU/PD:Value F10:Save ESC:Exit F1:General Help F5:Previous Values F6:Fail-Safe Defaults F7:Optimized Defaults Figure 6: PnP/PCI Configurations FPCI1/P CI5 IRQ Assignment 8Auto 83, 4, 5, 7, 9. , 10, 11, 12, 15 Auto assign IRQ to PCI 1/ PCI 5. (Default value) Set 3, 4, 5, 7, 9, 10, 11, 12, 15 to PCI1/ PCI5. FPCI2 IRQ Assignment 8Auto 83, 4, 5, 7, 9. , 10, 11, 12, 15 Auto assign IRQ to PCI 2. (Default value) Set 3, 4, 5, 7, 9, 10, 11, 12, 15 to PCI2. FPCI3 IRQ Assignment 8Auto 83, 4, 5, 7, 9. , 10, 11, 12, 15 Auto assign IRQ to PCI 3. (Default value) Set 3, 4, 5, 7, 9, 10, 11, 12, 15 to PCI3. FPCI4 IRQ Assignment 8Auto 83, 4, 5, 7, 9. , 10, 11, 12, 15 Auto assign IRQ to PCI 4. (Default value) Set 3, 4, 5, 7, 9, 10, 11, 12, 15 to PCI4. GA-8IE2004P(-L) Motherboard - 42 - English PC Health Status CMOS Setup Utility-Copyright (C) 1984-2003 Award Software PC Health Status Reset Case Open Status Case Opened VCORE Vcc18 +3. 3V +5V +12V Current CPU Temperature Current CPU FAN Speed Current SYSTEM FAN Speed CPU Warning Temperature CPU FAN Fail Warning SYSTEM FAN Fail Warning [Disabled] No 1. 488V 1. 776V 3. 296V 5. 053V 11. 840V 23°C 4440 RPM 0 RPM Disabled Disabled Disabled Item Help Menu Level higf: Move Enter:Select +/-/PU/PD:Value F10:Save ESC:Exit F1:General Help F5:Previous Values F6:Fail-Safe Defaults F7:Optimized Defaults Figure7: PC Health Status CReset Case Open Status CCase Opened If the case is closed, "Case Opened" will show "No". [. . . ] Make sure the jumper setting arecorrect. Please make sure all jumper settings (such as CPU system bus speed, frequency ratio, voltage and etc. ) are set properly. No Yes Failure hasbeen excluded. No Plug the CPU cooling fan pow er in the CPU fan connector. P lug in the AC power connector. Check if the CPU cooling fan attached to CPU properly. ls CPU cooling fan power connected to CPU_FAN properly? [. . . ]