User manual GIGABYTE GA-8IG

[. . . ] When you installing AGP card, please make sure the following notice is fully understood and practiced. If your AGP card has "AGP 4X notch"(show below), please make sure your AGP card is AGP 4X (1. 5V). Do not use AGP 2X card (3. 3V) in this motherboard. It will burn and damage the motherboard due to Intel® 845(E/G) / 850(E) chipset can't support AGP 2X(3. 3V). Example 1: Diamond Vipper V770 golden finger is compatible with 2X/ 4X mode AGP slot. [. . . ] Enable onboard Serial port 2 and address is 3F8. Enable onboard Serial port 2 and address is 2F8. (Default value) Enable onboard Serial port 2 and address is 3E8. Enable onboard Serial port 2 and address is 2E8. Disable onboard Serial port 2. Onboard Parallel port 378/IRQ7 278/IRQ5 Disabled 3BC/IRQ7 Enable onboard LPT port and address is 378/IRQ7. (Default Value) Enable onboard LPT port and address is 278/IRQ5. Enable onboard LPT port and address is 3BC/IRQ7. 33 GA-8IG Motherboard Parallel Port Mode SPP EPP ECP ECP+EPP Using Parallel port as Standard Parallel Port. (Default Value) Using Parallel port as Enhanced Parallel Port. Using Parallel port as Extended Capabilities Port. Using Parallel port as ECP & EPP mode. ECP Mode Use DMA 3 1 Set ECP Mode Use DMA to 3. (Default Value) Set ECP Mode Use DMA to 1. Game Port Address 201 209 Disabled Set Game Port Address to 201. (Default Value) Set Game Port Address to 209. Disable this function. Midi Port Address 300 330 Disabled Set Midi Port Address to 300. Set Midi Port Address to 330. (Default Value) Disable this function. Midi Port IRQ 5 10 Set Midi Port IRQ to 5. (Default Value) CIR Port Address 310 320 Disabled Set CIR Port Address to 310. (Default Value) CIR Port IRQ 5 11 Set CIR Port IRQ to 5. (Default Value) 34 BIOS Setup Power Management Setup CMOS Setup Utility-Copyright (C) 1984-2002 Award Software Power Management Setup ACPI Suspend Type Power LED in S1 state Soft-Off by PWR_BTTN PME Event Wake Up ModemRingOn Resume by Alarm x Date (of Month) Alarm x Time (hh:nn:ss) Power On By Mouse Power On By Keyboard x KB Power ON Password AC Back Function S1(POS) Blinking Instant-Off Enabled Enabled Disabled Everyday 000 Disabled Disabled Enter Soft-Off F1:General Help [S3] Set suspend type to Suspend to RAM under ACPI OS Item Help Menu Level [S1] Set suspend type to Power On Suspend under ACPI OS : Move Enter:Select +/-/PU/PD:Value F10:Save ESC:Exit F5:Previous Values F6:Fail-Safe Defaults Figure 5: Power Management Setup F7:Optimized Defaults ACPI Suspend Type S1(POS) S3(STR) Set ACPI suspend type to S1. (Default Value) Set ACPI suspend type to S3. Power LED in S1 state Blinking Dual/Off In standby mode(S1), power LED will blink. If use single color LED, power LED will turn off. If use dual color LED, power LED will turn to another color. Soft-off by PWR_BTTN Instant-off Press power button then Power off instantly. Enter suspend if button is pressed less than 4 sec. 35 GA-8IG Motherboard PME Event Wake Up Disabled Enabled Disable this function. [. . . ] Microsoft(R) Windows98 © Copyright Microsoft Corp 1981-1999 A:\> dir/w Volume in drive A has no label Volume Serial Number is 16EB-353D Directory of A:\ COMMAND. COM 3 file(s) 0 dir(s) 7VTX. F4 FLASH841. EXE 838, 954 bytes 324, 608 bytes free A:\> Flash841 7VTX. F4 (2) Now screen appears the following Flash Utility main menu. Press "Enter", the highlighted item will locate on the model name of the right-upper screen. Right after that, press "Enter" to start BIOS Flash Utility. 70 Appendix (3) It will pop up a screen and asks "Are you sure to flash the BIOS?" Press [Enter] to continue the procedure, or press [ESC] to quit. Beware: Please do not turn off the system while you are upgrading BIOS. [. . . ]