User manual GIGABYTE GA-8IG1000

[. . . ] When you installing AGP card, please make sure the following notice is fully understood and practiced. If your AGP card has "AGP 4X/8X (1. 5V) notch"(show below), please make sure your AGP card is AGP 4X/8X (1. 5V). AGP 4X/8X notch Caution: AGP 2X card is not supported by Intel® 845(GE/PE) / 845(E/G) / 850(E) / E7205 / 865(G/PE/P) / 875P. You might experience system unable to boot up normally. Example 1: Diamond Vipper V770 golden finger is compatible with 2X/4X mode AGP slot. [. . . ] If you use FSB400 Pentium 4 processor, please set "CPU Host Frequency" to 100MHz. If you use FSB533 Pentium 4 processor, please set "CPU Host Frequency" to 133MHz. If you use FSB800 Pentium 4 processor, please set "CPU Clock" to 200MHz. Incorrect using it may cause your system broken. For power End-User use only! AGP/PCI/SRC Fixed Serial ATA device is very sensitive to SRC clock. SRC over clock may make Serial ATA device function can't work properly. Adjust AGP/PCI/SRC clock asynchronous with CPU. Memory Frequency For for FSB(Front Side Bus) frequency=400MHz, 2. 66 Memory Frequency = Host clock X 2. 66. Auto Set Memory frequency by DRAM SPD data. (Default value) for FSB(Front Side Bus) frequency=533MHz, 2. 0 Memory Frequency = Host clock X 2. 0. 2. 5 Memory Frequency = Host clock X 2. 5. Auto Set Memory frequency by DRAM SPD data. (Default value) for FSB(Front Side Bus) frequency=800MHz, 2. 0 1. 6 1. 33 Auto Memory Frequency = Host clock X 2. 0. (Default value) Memory Frequency(Mhz) The values depend on CPU Host Frequency(Mhz). GA-8IG1000 Series Motherboard - 54 - AGP/PCI/SRC Frequency(Mhz) The values depend on Fixed AGP/PCI/SRC Frequency. English AGP OverVoltage Control Normal +0. 1V +0. 2V +0. 3V Set Set Set Set AGP AGP AGP AGP OverVoltage OverVoltage OverVoltage OverVoltage Control Control Control Control to to to to Normal. +0. 3V. DIMM OverVoltage Control Normal +0. 1V +0. 2V +0. 3V Set Set Set Set DIMM DIMM DIMM DIMM OverVoltage OverVoltage OverVoltage OverVoltage Control Control Control Control to to to to Normal. +0. 3V. CPU Voltage Control Supports adjustable CPU Vcore from 0. 8375V to 1. 7600V by 0. 025V step. (Default value: Normal) Normal CPU Vcore Display your CPU Vcore Voltage. - 55 - BIOS Setup English Select Language (*) CMOS Setup Utility-Copyright (C) 1984-2003 Award Software Standard CMOS Features Advanced BIOS Features Integrated Peripherals Power Management Setup PnP/PCI Configurations PC Health Status Frequency/Voltage Control ESC: Quit F8: Dual BIOS * / Q-Flash () Select Language (*) Load Fail-Safe Defaults Load Optimized Defaults Set Supervisor Password Set User Password Save & Exit Setup Exit Without Saving F3: Change Language ( *) F10: Save & Exit Setup Figure 9: Select Language Select Language Multi-Language supports 7 languages. There are English, Japanese, French, Spanish, German, Simplified Chinese, Traditional Chinese. () * For GA-8IG1000 Pro-G only. - 56 - GA-8IG1000 Series Motherboard Load Fail-Safe Defaults CMOS Setup Utility-Copyright (C) 1984-2003 Award Software Standard CMOS Features Advanced BIOS Features Integrated Peripherals Power Management Setup PnP/PCI Configurations PC Health Status Select Language (*) Load Fail-Safe Defaults Load Optimized Defaults Set Supervisor Password Set User Password Save & Exit Setup Exit Without Saving F3: Change Language ( *) () English Load Fail-Safe Defaults (Y/N) ?Y Frequency/Voltage Control ESC: Quit F8: Dual BIOS * / Q-Flash F10: Save & Exit Setup Load Fail-Safe Defaults Figure 10: Load Fail-Safe Defaults Load Fail-Safe Defaults Fail-Safe defaults contain the most appropriate values of the system parameters that allow minimum system performance. () * For GA-8IG1000 Pro-G only. - 57 BIOS Setup English Load Optimized Defaults CMOS Setup Utility-Copyright (C) 1984-2003 Award Software Standard CMOS Features Advanced BIOS Features Integrated Peripherals Power Management Setup PnP/PCI Configurations PC Health Status Select Language (*) Load Fail-Safe Defaults Load Optimized Defaults Set Supervisor Password Set User Password Save & Exit Setup Exit Without Saving F3: Change Language ( *) () Load Optimized Defaults (Y/N) ?Y Frequency/Voltage Control ESC: Quit F8: Dual BIOS * / Q-Flash F10: Save & Exit Setup Load Optimized Defaults Figure 11: Load Optimized Defaults Load Optimized Defaults Selecting this field loads the factory defaults for BIOS and Chipset Features which the system automatically detects. () * For GA-8IG1000 Pro-G only. - 58 - GA-8IG1000 Series Motherboard Set Supervisor/User Password CMOS Setup Utility-Copyright (C) 1984-2003 Award Software Standard CMOS Features Advanced BIOS Features Integrated Peripherals Power Management Setup PnP/PCI Configurations PC Health Status Select Language (*) Load Fail-Safe Defaults Load Optimized Defaults Set Supervisor Password Set User Password Save & Exit Setup Exit Without Saving F3: Change Language ( *) () English Enter Password : Frequency/Voltage Control ESC: Quit F8: Dual BIOS * / Q-Flash F10: Save & Exit Setup Change/Set/Disable Password Figure 12: Password Setting When you select this function, the following message will appear at the center of the screen to assist you in creating a password. Type the password, up to eight characters, and press <Enter>. You will be asked to confirm the password. Type the password again and press <Enter>. [. . . ] Support : http://tw. giga-byte. com/TechSupport/ServiceCenter. htm Non-Tech. Support(Sales/Marketing) : http://ggts. gigabyte. com. tw/nontech. asp WEB address : http://www. gigabyte. de Japan NIPPON GIGA-BYTE CORPORATION WEB address : http://www. gigabyte. co. jp Singapore GIGA-BYTE SINGAPORE PTE. Support : http://tw. giga-byte. com/TechSupport/ServiceCenter. htm Non-Tech. Support(Sales/Marketing) : http://ggts. gigabyte. com. tw/nontech. asp WEB address: http://www. gigabyte. com. sg U. K. [. . . ]