User manual GIGABYTE GA-8IG1000 PRO-G

[. . . ] When you installing AGP card, please make sure the following notice is fully understood and practiced. If your AGP card has "AGP 4X/8X (1. 5V) notch"(show below), please make sure your AGP card is AGP 4X/8X (1. 5V). AGP 4X/8X notch Caution: AGP 2X card is not supported by Intel® 845(GE/PE) / 845(E/G) / 850(E) / E7205 / 865(G/PE/P) / 875P. You might experience system unable to boot up normally. Example 1: Diamond Vipper V770 golden finger is compatible with 2X/4X mode AGP slot. [. . . ] If you use FSB400 Pentium 4 processor, please set "CPU Host Frequency" to 100MHz. If you use FSB533 Pentium 4 processor, please set "CPU Host Frequency" to 133MHz. If you use FSB800 Pentium 4 processor, please set "CPU Clock" to 200MHz. Incorrect using it may cause your system broken. For power End-User use only! AGP/PCI/SRC Fixed Serial ATA device is very sensitive to SRC clock. SRC over clock may make Serial ATA device function can't work properly. Adjust AGP/PCI/SRC clock asynchronous with CPU. Memory Frequency For for FSB(Front Side Bus) frequency=400MHz, 2. 66 Memory Frequency = Host clock X 2. 66. Auto Set Memory frequency by DRAM SPD data. (Default value) for FSB(Front Side Bus) frequency=533MHz, 2. 0 Memory Frequency = Host clock X 2. 0. 2. 5 Memory Frequency = Host clock X 2. 5. Auto Set Memory frequency by DRAM SPD data. (Default value) for FSB(Front Side Bus) frequency=800MHz, 2. 0 1. 6 1. 33 Auto Memory Frequency = Host clock X 2. 0. (Default value) Memory Frequency(Mhz) The values depend on CPU Host Frequency(Mhz). GA-8IG1000 Series Motherboard - 54 - AGP/PCI/SRC Frequency(Mhz) The values depend on Fixed AGP/PCI/SRC Frequency. English AGP OverVoltage Control Normal +0. 1V +0. 2V +0. 3V Set Set Set Set AGP AGP AGP AGP OverVoltage OverVoltage OverVoltage OverVoltage Control Control Control Control to to to to Normal. +0. 3V. DIMM OverVoltage Control Normal +0. 1V +0. 2V +0. 3V Set Set Set Set DIMM DIMM DIMM DIMM OverVoltage Control to Normal. (Default value) OverVoltage Control to +0. 1V. OverVoltage Control to +0. 3V. CPU Voltage Control Supports adjustable CPU Vcore from 0. 8375V to 1. 7600V by 0. 025V step. (Default value: Normal) Normal CPU Vcore Display your CPU Vcore Voltage. - 55 - BIOS Setup English Select Language (*) CMOS Setup Utility-Copyright (C) 1984-2003 Award Software Standard CMOS Features Advanced BIOS Features Integrated Peripherals Power Management Setup PnP/PCI Configurations PC Health Status Frequency/Voltage Control ESC: Quit F8: Dual BIOS (*) / Q-Flash Select Language (*) Load Fail-Safe Defaults Load Optimized Defaults Set Supervisor Password Set User Password Save & Exit Setup Exit Without Saving F3: Change Language (*) F10: Save & Exit Setup Figure 9: Select Language Select Language Multi-Language supports 7 languages. There are English, Japanese, French, Spanish, German, Simplified Chinese, Traditional Chinese. () * For GA-8IG1000 Pro-G only. - 56 - GA-8IG1000 Series Motherboard English Load Fail-Safe Defaults CMOS Setup Utility-Copyright (C) 1984-2003 Award Software Standard CMOS Features Advanced BIOS Features Integrated Peripherals Power Management Setup PnP/PCI Configurations PC Health Status Select Language (*) Load Fail-Safe Defaults Load Optimized Defaults Set Supervisor Password Set User Password Save & Exit Setup Exit Without Saving F3: Change Language (*) F10: Save & Exit Setup Load Fail-Safe Defaults Figure 10: Load Fail-Safe Defaults Load Fail-Safe Defaults (Y/N) ?Y Frequency/Voltage Control ESC: Quit F8: Dual BIOS (*) / Q-Flash Load Fail-Safe Defaults Fail-Safe defaults contain the most appropriate values of the system parameters that allow minimum system performance. () * For GA-8IG1000 Pro-G only. - 57 BIOS Setup English Load Optimized Defaults CMOS Setup Utility-Copyright (C) 1984-2003 Award Software Standard CMOS Features Advanced BIOS Features Integrated Peripherals Power Management Setup PnP/PCI Configurations PC Health Status Select Language (*) Load Fail-Safe Defaults Load Optimized Defaults Set Supervisor Password Set User Password Save & Exit Setup Exit Without Saving F3: Change Language (*) F10: Save & Exit Setup Load Optimized Defaults Figure 11: Load Optimized Defaults Load Optimized Defaults (Y/N) ?Y Frequency/Voltage Control ESC: Quit F8: Dual BIOS (*) / Q-Flash Load Optimized Defaults Selecting this field loads the factory defaults for BIOS and Chipset Features which the system automatically detects. () * For GA-8IG1000 Pro-G only. - 58 - GA-8IG1000 Series Motherboard English Set Supervisor/User Password CMOS Setup Utility-Copyright (C) 1984-2003 Award Software Standard CMOS Features Advanced BIOS Features Integrated Peripherals Power Management Setup PnP/PCI Configurations PC Health Status Select Language (*) Load Fail-Safe Defaults Load Optimized Defaults Set Supervisor Password Set User Password Save & Exit Setup Exit Without Saving F3: Change Language (*) F10: Save & Exit Setup Change/Set/Disable Password Figure 12: Password Setting Enter Password : Frequency/Voltage Control ESC: Quit F8: Dual BIOS (*) / Q-Flash When you select this function, the following message will appear at the center of the screen to assist you in creating a password. Type the password, up to eight characters, and press <Enter>. You will be asked to confirm the password. [. . . ] Yes Failure has been excluded. Insert the VGA card. Then plug in ATX power cable and turn on the system. A GA-8IG1000 Series Motherboard - 94 - English A The problem could be caused by power supply, CPU, memory or CPU/memory socket itself. Is memory LED on and CPU fan running? No Yes Failure has been excluded. No Check if there is display. Perhaps your VGA card / VGA slot or monitor is defective. Yes Turn off the system. Reboot after keyboard and mouse have been plugged in. Failure has been excluded. Check if keyboard is working properly. No It is possible that your keyboard or keyboard connector is defective. Yes Press <Del> to enter BIOS setup. [. . . ]