User manual GIGABYTE GA-8IG1000MF

[. . . ] When you installing AGP card, please make sure the following notice is fully understood and practiced. If your AGP card has "AGP 4X/8X (1. 5V) notch"(show below), please make sure your AGP card is AGP 4X/8X (1. 5V). AGP 4X/8X notch Caution: AGP 2X card is not supported by Intel® 845(GE/PE) / 845(E/G) / 850(E) / E7205 / 865(G/PE/P) / 875P. You might experience system unable to boot up normally. Example 1: Diamond Vipper V770 golden finger is compatible with 2X/4X mode AGP slot. [. . . ] SRC over clock may make Serial ATA device function can't work properly. Adjust AGP/PCI/SRC clock asychrohous with CPU. Memory Frequency For for FSB(Front Side Bus) frequency=400MHz, 2. 66 Auto 2. 0 2. 5 Auto Memory Frequency = Host clock X 2. 66. (Default value) Memory Frequency = Host clock X 2. 0. (Default value) for FSB(Front Side Bus) frequency=533MHz, for FSB(Front Side Bus) frequency=800MHz, 2. 0 1. 6 1. 33 Auto Memory Frequency = Host clock X 2. 0. (Default value) Memory Frequency (Mhz) The values depend on CPU Host Frequency(Mhz) . AGP/PCI/SRC Frequency (Mhz) The values depend on Fixed AGP/PCI/SRC Frequency. - 51 - BIOS Setup English Load Fail-Safe Defaults CMOS Setup Utility-Copyright (C) 1984-2003 Award Software Standard CMOS Features Advanced BIOS Features Integrated Peripherals Load Fail-Safe Defaults Load Optimized Defaults Set Supervisor Password Load Power Management Setup Fail-Safe Defaults (Y/N) ?Password Set User Y PnP/PCI Configurations PC Health Status Frequency/Voltage Control ESC: Quit F8: Q-Flash : Select Item F10: Save & Exit Setup Load Fail-Safe Defaults Figure 9: Load Fail-Safe Defaults Save & Exit Setup Exit Without Saving Load Fail-Safe Defaults Fail-Safe defaults contain the most appropriate values of the system parameters that allow minimum system performance. GA-8IG1000MF Series Motherboard - 52 - Load Optimized Defaults CMOS Setup Utility-Copyright (C) 1984-2003 Award Software Standard CMOS Features Advanced BIOS Features Integrated Peripherals Load Fail-Safe Defaults Load Optimized Defaults Set Supervisor Password English Load Power Management Setup Optimized Defaults (Y/N) ?Password Set User Y PnP/PCI Configurations PC Health Status Frequency/Voltage Control ESC: Quit F8: Q-Flash : Select Item F10: Save & Exit Setup Load Optimized Defaults Figure 10: Load Optimized Defaults Save & Exit Setup Exit Without Saving Load Optimized Defaults Selecting this field loads the factory defaults for BIOS and Chipset Features which the system automatically detects. - 53 - BIOS Setup English Set Supervisor/User Password CMOS Setup Utility-Copyright (C) 1984-2003 Award Software Standard CMOS Features Advanced BIOS Features Integrated Peripherals Load Fail-Safe Defaults Load Optimized Defaults Set Supervisor Password Set User Password Save & Exit Setup Exit Without Saving Enter Password : Power Management Setup PnP/PCI Configurations PC Health Status Frequency/Voltage Control ESC: Quit F8: Q-Flash : Select Item F10: Save & Exit Setup Change/Set/Disable Password Figure 11: Password Setting When you select this function, the following message will appear at the center of the screen to assist you in creating a password. Type the password, up to eight characters, and press <Enter>. You will be asked to confirm the password. Type the password again and press <Enter>. You may also press <Esc> to abort the selection and not enter a password. To disable password, just press <Enter> when you are prompted to enter password. A message "PASSWORD DISABLED" will appear to confirm the password being disabled. Once the password is disabled, the system will boot and you can enter Setup freely. The BIOS Setup program allows you to specify two separate passwords: SUPERVISOR PASSWORD and a USER PASSWORD. When disabled, anyone may access all BIOS Setup program function. When enabled, the Supervisor password is required for entering the BIOS Setup program and having full configuration fields, the User password is required to access only basic items. If you select "System" at "Password Check" in Advance BIOS Features Menu, you will be prompted for the password every time the system is rebooted or any time you try to enter Setup Menu. If you select "Setup" at "Password Check" in Advance BIOS Features Menu, you will be prompted only when you try to enter Setup. GA-8IG1000MF Series Motherboard - 54 - Save & Exit Setup CMOS Setup Utility-Copyright (C) 1984-2003 Award Software Standard CMOS Features Advanced BIOS Features Integrated Peripherals Load Fail-Safe Defaults Load Optimized Defaults Set Supervisor Password English (Y/N) ?Y Power Management Save to CMOS and EXITSet User Password Setup PnP/PCI Configurations PC Health Status Frequency/Voltage Control ESC: Quit F8: Q-Flash : Select Item F10: Save & Exit Setup Save Data to CMOS Figure 12: Save & Exit Setup Save & Exit Setup Exit Without Saving Type "Y" will quit the Setup Utility and save the user setup value to RTC CMOS. Type "N" will return to Setup Utility. - 55 - BIOS Setup English Exit Without Saving CMOS Setup Utility-Copyright (C) 1984-2003 Award Software Standard CMOS Features Advanced BIOS Features Integrated Peripherals Load Fail-Safe Defaults Load Optimized Defaults Set Supervisor Password Quit Power Management Setup Without Saving (Y/N) ?N Password Set User PnP/PCI Configurations PC Health Status Frequency/Voltage Control ESC: Quit F8: Q-Flash : Select Item F10: Save & Exit Setup Abandon all Data Figure 13: Exit Without Saving Save & Exit Setup Exit Without Saving Type "Y" will quit the Setup Utility without saving to RTC CMOS. Type "N" will return to Setup Utility. GA-8IG1000MF Series Motherboard - 56 - Chapter 4 Technical Reference @BIOSTM Introduction Gigabyte announces @BIOSTM Windows BIOS live update utility Have you ever updated BIOS by yourself? [. . . ] No Insert and push the memory module vertically into the DIMM slot. Check if the memory install properly into the DIMM slot. Yes Failure has been excluded. Insert the VGA card. Then plug in ATX power cable and turn on the system. A - 93 - Appendix English A The problem could be caused by power supply, CPU, memory or CPU/memory socket itself. Is memory LED on and CPU fan running? No Yes Failure has been excluded. No Check if there is display. Perhaps your VGA card / VGA slot or monitor is defective. Yes Turn off the system. [. . . ]