User manual GIGABYTE GA-8PE667

[. . . ] When you installing AGP card, please make sure the following notice is fully understood and practiced. If your AGP card has "AGP 4X notch"(show below), please make sure your AGP card is AGP 4X (1. 5V). Caution: AGP 2X card is not supported by Intel® 845(GE/PE) / 845(E/G) / 850(E). You might experience system unable to boot up normally. Example 1: Diamond Vipper V770 golden finger is compatible with 2X/4X mode AGP slot. [. . . ] (Default Value) Set ECP Mode Use DMA to 1. - 33 - BIOS Setup English CGame Port Address 8201 8209 8Disabled Set Game Port Address to 201. (Default Value) Set Game Port Address to 209. Disable this function. CMidi Port Address 8300 8330 8Disabled Set Midi Port Address to 300. Set Midi Port Address to 330. (Default Value) Disable this function. CMidi Port IRQ 85 810 Set Midi Port IRQ to 5. (Default Value) GA-8PE667 Motherboard - 34 - English Power Management Setup CMOS Setup Utility -Copy right (C) 1984-2002 Aw ard Softw are Pow er Management Setup ACPI Suspend Ty pe Pow er LED in S1 state Soft-Off by PWR_BTTN PME Ev ent Wake Up ModemRingOn Resume by Alarm x Date (of Month) Alarm x Time (hh:nn:ss) Pow er On By Mouse Pow er On By Key board x KB Pow er ON Passw ord AC Back Function [S1(POS)] [Blinking] [Instant-Off] [Enabled] [Enabled] [Disabled] Ev ery day 000 [Disabled] [Disabled] Enter [Soft-Off] F1:General Help [S3] Set suspend ty pe to Suspend to RAM under ACPI OS Item Help Menu Lev el u [S1] Set suspend ty pe to Pow er On Suspend under ACPI OS higf: Mov e Enter:Select +/-/PU/PD:Value F10:Sav e ESC:Ex it F5:Prev ious Values F6:Fail-Safe Defaults Figure 5: Pow er Management Setup F7:Optimized Defaults C ACPI Suspend Type 8S1(POS) 8S3(STR) Set ACPI suspend ty pe to S1. (Default Value) Set ACPI suspend ty pe to S3. C Power LED i n S1 state 8Blinking 8Dual/OFF In standby mode(S1), pow er LED w ill blink. If use single color LED, pow er LED w ill turn off. If use dual color LED, pow er LED w ill turn to another color. C Soft-off by PWR_BTT N 8Instant-off 8Delay 4 Sec. Press pow er button then Pow er off instantly . (Default v alue) Press pow er button 4 sec to Pow er off. Enter suspend if button is pressed less than 4 sec. - 35 - BIOS Setup English C PME Event Wake Up 8Disabled 8Enabled Disable this function. (Default Value) C ModemRingOn 8Disabled 8Enabled Disable Modem Ring on function. (Default Value) C Resume by Alarm You can set "Resume by Alarm" item to enabled and key in Data/time to pow er on sy stem. 8Disabled 8Enabled Disable this function. (Default Value) Enable alarm function to POWER ON sy stem. If RTC Alarm Lead To Pow er On is Enabled. Date ( of Month) Alarm : Time ( hh: mm: ss) Alarm : Ev ery day , 1~31 (0~23) : (0~59) : (0~59) C Power On By Mouse 8Disabled 8Mouse Click Disabled this function. (Default v alue) Double click on PS/2 mouse left button. C Power On By Keyboard 8Passw ord 8Disabled 8Key board 98 Enter from 1 to 5 characters to set the Key board Pow er On Passw ord. (Default v alue) If y our key board hav e "POWER Key " button, y ou can press the key to pow er on y our sy stem. CKB Power ON Password 8Enter Input passw ord (from 1 to 5 characters) and press Enter to set the Key board Pow er On Passw ord. CAC Back Function 8Memory 8Soft-Off 8Full-On Sy stem pow er on depends on the status before AC lost. (Default v alue) Alw ay s pow er on the sy stem w hen AC back. GA-8PE667 Motherboard - 36 - English PnP/PCI Configurations CMOS Setup Utility -Copy right (C) 1984-2002 Aw ard Softw are PnP/PCI Configurations PCI 1/PCI 5 IRQ Assignment PCI 2 IRQ Assignment PCI 3 IRQ Assignment PCI 4 IRQ Assignment [Auto] [Auto] [Auto] [Auto] Item Help Menu Lev el u higf: Mov e Enter:Select +/-/PU/PD:Value F10:Sav e ESC:Ex it F5:Prev ious Values F6:Fail-Safe Defaults Figure 6: PnP/PCI Configurations F1:General Help F7:Optimized Defaults C PCI 1/PCI 5 IRQ Ass ignment 8Auto 83, 4, 5, 7, 9, 10, 11, 12, 14, 15 Auto assign IRQ to PCI 1/PCI 5. (Default v alue) Set IRQ 3, 4, 5, 7, 9, 10, 11, 12, 14, 15 to PCI 1/PCI 5. C PCI 2 IRQ Assignment 8Auto 83, 4, 5, 7, 9, 10, 11, 12, 14, 15 Auto assign IRQ to PCI 2. (Default v alue) Set IRQ 3, 4, 5, 7, 9, 10, 11, 12, 14, 15 to PCI 2. C PCI 3 IRQ Assignment 8Auto 83, 4, 5, 7, 9, 10, 11, 12, 14, 15 Auto assign IRQ to PCI 3. (Default v alue) Set IRQ 3, 4, 5, 7, 9, 10, 11, 12, 14, 15 to PCI 3. - 37 - BIOS Setup English PC Health Status CMOS Setup Utility -Copy right (C) 1984-2002 Aw ard Softw are PC Health Status Reset Case Open Status Case Opened VCORE +1. 5V +3. 3V +5V +12V Current CPU Temperature Current CPU FAN Speed Current SYSTEM FAN Speed CPU Warning Temperature CPU FAN Fail Warning SYSTEM FAN Fail Warning [Disabled] [No] 1. 71V 1. 488V 3. 29V 4. 99V 11. 73V 40°C 4821 RPM 0 RPM [Disabled] [Disabled] [Disabled] Item Help Menu Lev el u higf: Mov e Enter:Select +/-/PU/PD:Value F10:Sav e ESC:Ex it F1:General Help F5:Prev ious Values F6:Fail-Safe Defaults F7:Optimized Defaults Figure 7: PC Health Status CReset Case Open Status CCase Opened If the case is closed, "Case Opened" w ill show "No". [. . . ] Cable with rear bracket is provided and could link to the " SPDIF output"connector (As picture. ) For the further linkage to decoder, rear bracket provides coaxial cable and Fiber connecting port. 1. Connect the SPDIF output device to the rear bracket of PC, and fix it with screw. 2. Connect SPDIF device to the m otherboard. 3. Connect SPDIF to the SPDIF decoder. GA-8PE667 Motherboard - 72 - English - 73 - Technical Reference English GA-8PE667 Motherboard - 74 - Revision History Chapter 5 Appendix Picture below are shown in Windows XP (CD driver version 1. 0) Appendix A: Chipset Driver Installation A. [. . . ]