User manual GIGABYTE GA-8S648FXM

[. . . ] When you installing AGP card, please make sure the following notice is fully understood and practiced. If your AGP card has "AGP 4X/8X (1. 5V) notch" (show below), please make sure your AGP card is AGP 4X/8X(1. 5V). AGP 4X/8X notch Caution: AGP 2X card is not supported by SiS® 648FX. You might experience system unable to boot up normally. Example 1: Diamond Vipper V770 golden finger is compatible with 2X/4X mode AGP slot. [. . . ] (Default Value) Power On by Mouse Disabled Enabled Disable this function. (Default Value) Enable Power On by move or click mouse function. GA-8S648FXM Motherboard - 44 - Resume by Alarm You can set "Resume by Alarm" item to enabled and key in Data/time to power on system. (Default Value) Enable alarm function to POWER ON system. English If RTC Alarm Lead To Power On is Enabled. Month Alarm : Day (of Month) : Time (hh : mm : ss) : NA, 1~12 1~31 (0~23) : (0~59) : (0~59) Power LED in S1 state Blinking Dual/OFF In standby mode(S1), power LED will blink. If use single color LED, power LED will turn off. If use dual color LED, power LED will turn to another color. - 45 - BIOS Setup English PnP/PCI Configurations CMOS Setup Utility-Copyright (C) 1984-2003 Award Software PnP/PCI Configurations PCI 1 IRQ Assignment PCI 2 IRQ Assignment PCI 3 IRQ Assignment [Auto] [Auto] [Auto] Device(s) using this INT: Display Cntrlr -BUS 1 Dev 2 Func 3 : Move Enter:Select +/-/PU/PD:Value F10:Save F6:Fail-Safe Defaults ESC:Exit F1:General Help Item Help Menu Level F5:Previous Values F7:Optimized Defaults Figure 6: PnP/PCI Configurations PCI 1 IRQ Assignment Auto 3, 4, 5, 7, 9, 10, 11, 12, 14, 15 Auto assign IRQ to PCI 1. (Default value) Set IRQ 3, 4, 5, 7, 9, 10, 11, 12, 14, 15 to PCI 1. PCI 2 IRQ Assignment Auto 3, 4, 5, 7, 9, 10, 11, 12, 14, 15 Auto assign IRQ to PCI 2. (Default value) Set IRQ 3, 4, 5, 7, 9, 10, 11, 12, 14, 15 to PCI 2. PCI 3 IRQ Assignment Auto 3, 4, 5, 7, 9, 10, 11, 12, 14, 15 Auto assign IRQ to PCI 3. (Default value) Set IRQ 3, 4, 5, 7, 9, 10, 11, 12, 14, 15 to PCI 3. GA-8S648FXM Motherboard - 46 - PC Health Status CMOS Setup Utility-Copyright (C) 1984-2003 Award Software PC Health Status Reset Case Open Status Case Opened Vcore VCC18 +3. 3V +5V +12V Current System Temperature Current CPU Temperature Current CPU FAN Speed Current SYSTEM FAN Speed CPU Warning Temperature CPU FAN Fail Warning SYSTEM FAN Fail Warning : Move [Disabled] No 1. 778V 1. 856V 3. 2V 4. 945V 12. 288V 33°C 68°C 5113 RPM 0 RPM [Disabled] [Disabled] [Disabled] ESC:Exit F1:General Help [Enabled] Clear case open status at next boot Item Help Menu Level [Disabled] Don't reset case open status English Enter:Select +/-/PU/PD:Value F10:Save Figure 7: PC Health Status F5:Previous Values F6:Fail-Safe Defaults F7:Optimized Defaults Reset Case Open Status Case Opened If the case is closed, "Case Opened" will show "No". If the case have been opened, "Case Opened" will show "Yes". If you want to reset "Case Opened" value, set "Reset Case Open Status" to "Enabled" and save CMOS, your computer will restart. Current Voltage (V) Vcore / VCC18 / +3. 3V / +5V / +12V Detect system's voltage status automatically. - 47 - BIOS Setup English Current System / CPU Temperature Detect System/CPU temperature automatically. Current CPU/SYSTEM FAN Speed (RPM) Detect CPU/System Fan speed status automatically. CPU Warning Temperature Disabled 60°/140°F 70°/158°F 80°/176°F 90°/194°F Don't monitor CPU's temperature. (Default value) Alarm when CPU current temperature over than 60°/140°F. Alarm when CPU current temperature over than 70°/158°F. Alarm when CPU current temperature over than 80°/176°F. Alarm when CPU current temperature over than 90°/194°F. CPU FAN Fail Warning Disabled Enabled Fan Warning function disable. (Default value) Enalbe FAN warning alarm when FAN stops. SYSTEM FAN Fail Warning Disabled Enabled Fan Warning function disable. (Default value) Enalbe FAN warning alarm when FAN stops. GA-8S648FXM Motherboard - 48 - Frequency/Voltage Control CMOS Setup Utility-Copyright (C) 1984-2003 Award Software Frequency/Voltage Control CPU Clock Ratio Linear Frequency Control x CPU Clock (MHz) x DRAM Clock (MHz) AGP/PCI Clock Control x AGP Clock (MHz) x PCI Clock (MHz) [15X] [Disabled] 100 AUTO [AUTO] 66 33 Item Help Menu Level English : Move Enter:Select +/-/PU/PD:Value F10:Save F6:Fail-Safe Defaults Figure 8: Frequency/Voltage Control ESC:Exit F1:General Help F5:Previous Values F7:Optimized Defaults CPU Clock Ratio This option will not be shown or not be available if you are using a CPU with the locked ratio. 15X~21X It's depends on CPU Clock Ratio. Linear Frequency Control Disabled Enabled Disable this function. (Default value) Enable this function. CPU Clock (MHz) 100~355 Select CPU Clock to 100MHz~355MHz. Incorrect using it may cause your system broken. For power End-User use only! - 49 - BIOS Setup English DRAM Clock (MHz) This feature allows you to adjust the DRAM frequency, When "Linear Frequency Control" is set to Enabled. Please set DRAM Clock according to your requirement. [. . . ] Advanced BIOS features--> First boot device: "SCSI" Then it depends on the mode(RAID or ATA) that you need to set in RAID/ SCSI BIOS. GA-8S648FXM Motherboard - 84 - Troubleshooting If you encounter any trouble during boot up, please follow the troubleshooting procedures. START English Turn off the power and unplug the AC power cable, then remove all of the add-on cards and cables from motherboard. Please make sure motherboard & chassis are not short ? Yes Please isolate the short pin. No Failure has been excluded. Please make sure all jumper settings (such as CPU system bus speed, frequency ratio, voltage and etc) are set properly. No Make sure the jumper setting are correct. Yes Failure has been excluded. No Plug the CPU cooling fan power in the CPU fan connector. Plug in the AC power connector. Check if the CPU cooling fan attached to CPU properly. ls CPU cooling fan power connected to CPU_FAN properly? [. . . ]