User manual GIGABYTE GA-8SQ800

[. . . ] When you installing AGP card, please make sure the following notice is fully understood and practiced. If your AGP card has "AGP 4X/8X(1. 5V) notch"(show below), please make sure your AGP card is AGP 4X/8X(1. 5V). AGP 4X/8X notch Caution: AGP 2X card is not supported by SiS 655. You might experience system unable to boot up normally. Please insert an AGP 4X/8X card. ® Example 1: Diamond Vipper V770 golden finger is compatible with 2X/4X mode AGP slot. [. . . ] For W illamette CPU: 8X~23X default: 14X For C -Steppin g P4: 8X, 10X~24X default: 15X For N orthwood CPU: 12X~24X default: 16X The option w ill display "Locked" and read only if the CPU ratio is not changeable. Linear Frequency Control 8Disabled 8Enabled Disable this function. (Default v alue) Enable this function. CPU Clock (MHz) 8100~355 Select CPU Clock to 100MHz~355MHz. Incorrect using it may cause y our sy stem broken. For pow er End-User use only ! GA-8SQ800 Ultra/GA-8SQ800 Motherboard - 44 - DRAM Clock (MHz) 8Please set DRAM Clock according to y our requirement. If y ou use DDR266 DRAM module, please set "DRAM Clock(MHz)" to Auto or 266. If y ou use DDR333 DRAM module, please set "DRAM Clock(MHz)" to Auto or 333. Incorrect using it may cause y our sy stem broken. For pow er End-User use only ! English AGP/PCI Clock Control 8AUTO 8Manual Set AGP/PCI Clock Control to AUTO. (Default v alue) Set AGP/PCI Clock Control to Manual. AGP Clock (MHz) 8Please set AGP Clock according to y our requirement. Incorrect using it may cause y our sy stem broken. For pow er End-User use only ! PCI Clock (MHz) 8Please set PCI Clock according to y our requirement. Incorrect using it may cause y our sy stem broken. For pow er End-User use only ! AGP Voltag e Control 8Normal 8+0. 1V Set AGP Voltage Control to Normal. (Default v alue) Set AGP Voltage Control to +0. 1V. DRAM Voltage Control 8Normal 8+0. 1V Set DRAM Voltage Control to Normal. (Default v alue) Set DRAM Voltage Control to +0. 1V. CPU Voltag e Control 8 Supports adjustable CPU Vcore from 1. 575V to 1. 775V by 0. 025V step. (Default v alue: Normal) - 45 - BIOS Setup English Top Performance CMOS Setup Utility -Copy right (C) 1984-2002 Aw ard Softw are }Standard CMOS Features }Adv anced BIOS Features Top Performance Load Fail-Safe Defaults Load Optimized Defaults Set Superv isor Passw ord Set User Passw ord Sav e & Ex it Setup Ex it Without Sav ing higf:Select Item ENTER: Accept F10:Sav e & Ex it Setup Top Performance }Integrated Peripherals }Pow er Management Setup }PnP/PCI Configurations }PC Health Status Disabled. . . . . . . . . . . . . . . . . . . [ n] Enabled. . . . . . . . . . . . . . . . . . . [ ] }Frequency /Voltage Control ESC:Quithi: Mov e F8: Dual ESC: Abort BIOS**/Q-Flash Figure 9: Top Performance Top Performance If you wish to maximize the performance of your system, set "Top Performance" as "Enabled". 8Disabled Disable this function. (Default Value) 8Enabled Enable Top Performance function. You must check whether your RAM, CPU support over clock when you set "Top Performance" to "Enabled". "**" For GA-8SQ800 Ultra only. GA-8SQ800 Ultra/GA-8SQ800 Motherboard - 46 - English Load Fail-Safe Defaults CMOS Setup Utility -Copy right (C) 1984-2002 Aw ard Softw are }Standard CMOS Features }Adv anced BIOS Features }Integrated Peripherals }Pow er Management Setup }PnP/PCI Configurations }PC Health Status }Frequency /Voltage Control ESC:Quit F8: Dual BIOS**/Q-Flash Top Performance Load Fail-Safe Defaults Load Optimized Defaults Load Fail-Safe Defaults?(Y/N)?Y Set Superv isor Passw ord Set User Passw ord Sav e & Ex it Setup Ex it Without Sav ing higf:Select Item F10:Sav e & Ex it Setup Load Fail-Safe Defaults Figure 10: Load Fail-Safe Defaults Load Fail-Safe Defaults Fail-Safe defaults contain the most appropriate values of the system parameters that allow minimum system performance. "**" For GA-8SQ800 Ultra only. - 47 BIOS Setup English Load Optimized Defaults CMOS Setup Utility -Copy right (C) 1984-2002 Aw ard Softw are }Standard CMOS Features }Adv anced BIOS Features }Integrated Peripherals }Pow er Management Setup }PnP/PCI Configurations }PC Health Status }Frequency /Voltage Control ESC:Quit F8: Dual BIOS**/Q-Flash Top Performance Load Fail-Safe Defaults Load Optimized Defaults Set Superv isor Passw ord Set User Passw ord Sav e & Ex it Setup Ex it Without Sav ing higf:Select Item F10:Sav e & Ex it Setup Load Optimized Defaults Figure 11: Load Optimized Defaults Load Optimized Defaults?(Y/N)?Y Load Optimized Defaults Selecting this field loads the factory defaults for BIOS and Chipset Features which the system automatically detects. "**" For GA-8SQ800 Ultra only. GA-8SQ800 Ultra/GA-8SQ800 Motherboard - 48 - English Set Supervisor/User Password CMOS Setup Utility -Copy right (C) 1984-2002 Aw ard Softw are }Standard CMOS Features }Adv anced BIOS Features }Integrated Peripherals }Pow er Management Setup }PnP/PCI Configurations }PC Health Status }Frequency /Voltage Control ESC:Quit F8: Dual BIOS**/Q-Flash Top Performance Load Fail-Safe Defaults Load Optimized Defaults Set Superv isor Passw ord Set User Passw ord Sav e & Ex it Setup Ex it Without Sav ing higf:Select Item F10:Sav e & Ex it Setup Change/Set/Disable Passw ord Figure 12: Passw ord Setting Enter Password: When you select this function, the following message will appear at the center of the screen to assist you in creating a password. Type the password, up to eight characters, and press <Enter>. You will be asked to confirm the password. [. . . ] Address: Postbus 1385, 5602 BJ, Eindhoven, The Netherlands -- Taiwan Gigabyte Technology Co. , Ltd. Address: No. 6, Bau Chiang Road, Hsin-Tien, Taipei Hsien, Taiwan, R. O. C. TEL: 886 (2) 8912-4888 (50 lines) FAX: 886 (2) 8912-4004 E-mail:english@gigabyte. com. tw Web Address: http://www. gigabyte. com. tw -- USA G. B. T. Address: 17358 Railroad St, City of Industry, CA 91748. [. . . ]