User manual GIGABYTE GA-J1900M-D2P

[. . . ] No part of this manual may be reproduced, copied, translated, transmitted, or published in any form or by any means without GIGABYTE's prior written permission. In order to assist in the use of this product, carefully read the User's Manual. For product-related information, check on our website at: http://www. gigabyte. com Identifying Your Motherboard Revision The revision number on your motherboard looks like this: "REV: X. X. " For example, "REV: 1. 0" means the revision of the motherboard is 1. 0. Check your motherboard revision before updating motherboard BIOS, drivers, or when looking for technical information. [. . . ] Auto BIOS will automatically adjust the HT Link Frequency. (Default) x1~x10 Sets HT Link Frequency to x1~x10 (200 MHz~2. 0 GHz). PCIE Clock(MHz) HT Link Width HT Link Frequency Set Memory Clock Determines whether to manually set the memory clock. Auto lets BIOS automatically set the memory clock as required. Manual allows the memory clock control item below to be configurable. (Default: Auto) This item is present only when you install a CPU that supports this feature. - 24 - (Note) Memory Clock This option is configurable only when Set Memory Clock is set to Manual. X8. 00 Sets Memory Clock to X8. 00. DRAMConfiguration x x x x x x x x x x x x CMOS Setup Utility-Copyright (C) 1984-2011 Award Software DRAMConfiguration [Unganged] [Auto] SPD Auto -Auto 9T Auto 9T Auto 9T Auto 24T Auto 5T Auto 110ns Auto -Auto 10T Auto 5T Auto 33T Auto 4T [Enabled] [Enabled] [SkipDQS] [Disabled] +/-/PU/PD: Value F6: Fail-Safe Defaults F10: Save ESC: Exit F1: General Help F7: Optimized Defaults Auto -9T 9T 9T 24T 5T 110ns -10T 5T 33T 4T Item Help Menu Level DCTsMode DDR3TimingItems 1T/2T Command Timing CAS# latency RAS to CAS R/W Delay Row Precharge Time Minimum RAS Active Time TwTr Command Delay Trfc0 for DIMM1 Trfc1 for DIMM2 Write Recovery Time Precharge Time Row Cycle Time RAS to RAS Delay ChannelInterleaving BankInterleaving DQSTrainingControl Memclocktri-stating Enter: Select : Move F5: Previous Values DCTs Mode DDR3 Timing Items Allows you to set memory control mode. Ganged Sets memory control mode to single dual-channel. Unganged Sets memory control mode to two single-channel. (Default) 1T/2T Command Timing CAS# latency Manual allows all DDR3 Timing items below to be configurable. Options are: Auto (default), 90ns, 110ns, 160ns, 300ns, 350ns. The adjustable range is dependent on the CPU being installed. (Default: Normal) Note: Increasing CPU voltage may result in damage to your CPU or reduce the useful life of the CPU. - 26 - CPU Voltage Control Allows you to set the CPU voltage. The adjustable range is dependent on the CPU being installed. (Default: Normal) Note: Increasing CPU voltage may result in damage to your CPU or reduce the useful life of the CPU. Displays the normal operating voltage of your CPU. Normal CPU Vcore 2-4 Standard CMOS Features CMOS Setup Utility-Copyright (C) 1984-2011 Award Software Standard CMOS Features Date (mm:dd:yy) Time (hh:mm:ss) Tue, Aug 23 2011 22:31:24 [None] [None] [None] [None] [None] [None] [All, ButKeyboard] 640K 766M F10: Save ESC: Exit F1: General Help F7: Optimized Defaults Item Help Menu Level IDEChannel0Master IDEChannel0Slave IDEChannel1Master IDEChannel1Slave IDEChannel2Master IDEChannel2Slave HaltOn BaseMemory Extended Memory Enter: Select : Move F5: Previous Values +/-/PU/PD: Value F6: Fail-Safe Defaults Date (mm:dd:yy) Time (hh:mm:ss) Sets the system date. Sets the system time. IDE Channel 0, 1 Master/Slave IDE Channel 2 Master/Slave IDE Channel 0, 1 Master/Slave Configure your SATA devices by using one of the three methods below: · None If no SATA devices are used, set this item to None so the system will skip the detection of the device during the POST for faster system startup. · Auto Lets the BIOS automatically detect SATA devices during the POST. (Default) · Manual Allows you to manually enter the specifications of the hard drive when the hard drive access mode is set to CHS. Access Mode Sets the hard drive access mode. Options are: Auto (default), CHS, LBA, Large. Extended IDE Drive Configure your SATA devices by using one of the two methods below: · Auto Lets the BIOS automatically detect SATA devices during the POST. [. . . ] Press <Ctrl>+<Y> to set the capacity of the RAID array or press other keys to set the array to its maximum capacity. Press Ctrl-Y to Modify Array Capacity or press any other key to use maximum capacity. . . Figure 3 8. After the creation is complete, the screen will return to LD View Menu where you will see the newlycreated array. Press <Esc> to return to Main Menu and press <Esc> again if you want to exit the RAID BIOS utility. - 39 - Making a SATA RAID Driver Diskette Copy the driver for the SATA controller from the motherboard driver disk to a floppy disk (for Windows XP) or a USB flash drive (for Windows 7/Vista). For example, to copy the RAID driver for Windows XP 32-bit operating system, copy the driver from the following directory to your floppy disk: \BootDrv\SBxxx\x86. [. . . ]