User manual GIGABYTE GA-K8VT800-RH

[. . . ] GA-K8VT800-RH AMD Socket 754 Processor Motherboard User's Manual Rev. 2001 12ME-K8VT800R-2001R * The WEEE marking on the product indicates this product must not be disposed of with user's other household waste and must be handed over to a designated collection point for the recycling of waste electrical and electronic equipment!!* The WEEE marking applies only in European Union's member states. Motherboard GA-K8VT800-RH Motherboard GA-K8VT800-RH June. 21, 2006 Copyright © 2006 GIGA-BYTE TECHNOLOGY CO. , LTD. [. . . ] (Default value) Increase AGP voltage +0. 1V. Increase AGP voltage +0. 2V. GA-K8VT800-RH Motherboard - 42 - DIMM OverVoltage control Auto Supply DIMM voltage as DIMM required. (Default value) +0. 1V Increase DIMM voltage +0. 1V. Please note that by overclocking your system through the increase of the DDR voltage, damage to the memory may occur. English 2-8 Top Performance CMOS Setup Utility-Copyright (C) 1984-2004 Award Software Standard CMOS Features Advanced BIOS Features Integrated Peripherals Top Performance Power Management Setup Disabled. . . . . . . . . . . . . . . . . . . . . . . . . [ ] PnP/PCI Configurations Enabled. . . . . . . . . . . . . . . . . . . . . . . . . . [ ] PC Health Status Frequency/Voltage Control Esc: Quit F8: Q-Flash : Move ESC: Abort Top Performance Load Fail-Safe Defaults Load Optimized Defaults Set Supervisor Password Set User Password Save & Exit Setup Exit Without Saving : Select Item ENTER: Accept Save & Exit Setup F10: Load Fail-Safe Defaults If you wish to maximize the performance of your system, set "Top Performance" as "Enabled". (Default Value) Enabled Enable Top Performance function. "Top Performance" will increase hardware working speed. Different system configuration (both hardware component and OS) will effect the result. For example, the same hardware configuration might not run properly with Windows XP, but works smoothly with Windows NT. Therefore, if your system is not perform enough, the reliability or stability problem will appear sometimes, and we will recommend you disabling the option to avoid the problem as mentioned above. 2-9 Load Fail-Safe Defaults CMOS Setup Utility-Copyright (C) 1984-2004 Award Software Standard CMOS Features Advanced BIOS Features Integrated Peripherals Power Management Setup PnP/PCI Configurations PC Health Status Frequency/Voltage Control Esc: Quit F8: Q-Flash Top Performance Load Fail-Safe Defaults Load Optimized Defaults Set Supervisor Password Load Fail-Safe DefaultsSet User N (Y/N)?Password Save & Exit Setup Exit Without Saving : Select Item F10: Save & Exit Setup Load Fail-Safe Defaults Fail-Safe defaults contain the most appropriate values of the system parameters that allow minimum system performance. - 43 - BIOS Setup English 2-10 Load Optimized Defaults CMOS Setup Utility-Copyright (C) 1984-2004 Award Software Standard CMOS Features Advanced BIOS Features Integrated Peripherals Power Management Setup PnP/PCI Configurations PC Health Status Frequency/Voltage Control Esc: Quit F8: Q-Flash Load Optimized Defaults Top Performance Load Fail-Safe Defaults Load Optimized Defaults Set Supervisor Password Load Optimized Defaults (Y/N)?Password Set User N Save & Exit Setup Exit Without Saving : Select Item F10: Save & Exit Setup Selecting this field loads the factory defaults for BIOS and Chipset Features which the system automatically detects. 2-11 Set Supervisor/User Password CMOS Setup Utility-Copyright (C) 1984-2004 Award Software Standard CMOS Features Advanced BIOS Features Integrated Peripherals Power Management Setup PnP/PCI Configurations Enter Password: PC Health Status Frequency/Voltage Control Esc: Quit F8: Q-Flash Top Performance Load Fail-Safe Defaults Load Optimized Defaults Set Supervisor Password Set User Password Save & Exit Setup Exit Without Saving : Select Item F10: Save & Exit Setup Change/Set/Disable Password When you select this function, the following message will appear at the center of the screen to assist you in creating a password. Type the password, up to eight characters, and press <Enter>. You will be asked to confirm the password. Type the password again and press <Enter>. You may also press <Esc> to abort the selection and not enter a password. To disable password, just press <Enter> when you are prompted to enter password. A message "PASSWORD DISABLED" will appear to confirm the password being disabled. Once the password is disabled, the system will boot and you can enter Setup freely. The BIOS Setup program allows you to specify two separate passwords: SUPERVISOR PASSWORD and a USER PASSWORD. When disabled, anyone may access all BIOS Setup program function. When enabled, the Supervisor password is required for entering the BIOS Setup program and having full configuration fields, the User password is required to access only basic items. If you select "System" at "Password Check" in Advance BIOS Features Menu, you will be prompted for the password every time the system is rebooted or any time you try to enter Setup Menu. [. . . ] Question 5: Sometimes I hear different continuous beeps from computer after system boots up. Answer: The beep codes below may help you identify the possible computer problems. However, they are only for reference purposes. The situations might differ from case to case. [. . . ]