User manual GIGABYTE GO-B5232D

[. . . ] No part of this manual may be reproduced, copied, translated, transmitted, or published in any form or by any means without GIGABYTE's prior written permission. In order to assist in the use of this product, carefully read the User's Manual. For product-related information, check on our website at: http://www. gigabyte. com Identifying Your Motherboard Revision The revision number on your motherboard looks like this: "REV: X. X. " For example, "REV: 1. 0" means the revision of the motherboard is 1. 0. Check your motherboard revision before updating motherboard BIOS, drivers, or when looking for technical information. [. . . ] The adjustable range is from 100 MHz to 1200 MHz. This item is configurable only if the CPU Host Clock Control option is enabled. Important: It is highly recommended that the CPU frequency be set in accordance with the CPU specifications. Allows you to manually set the PCIe clock frequency. The adjustable range is from 90 MHz to 150 MHz. Auto sets the PCIe clock frequency to standard 100 MHz. (Default: Auto) & PCI Express Frequency (Mhz) ******** DRAM Performance Control ******** & Performance Enhance Allows the system to operate at three different performance levels. Standard Lets the system operate at its basic performance level. (Default) Turbo Lets the system operate at its good performance level. Extreme Lets the system operate at its best performance level. Allows you to fix the chipset frequency at system bootup. Disabled Disables this function. & DDR Write Training & Channel A/B Driving Settings CMOS Setup Utility-Copyright (C) 1984-2011 Award Software Channel A/B Driving Settings x Driving Strength Profile x x x x x x x x Data Driving Pull-Up Level Cmd Driving Pull-Up Level Ctrl Driving Pull-Up Level Clk Driving Pull-Up Level Data Driving Pull-Down Lev Cmd Driving Pull-Down Lev Ctrl Driving Pull-Down Lev Clk Driving Pull-Down Lev Auto Auto Auto Auto Auto Auto Auto Auto Auto +/-/PU/PD: Value F6: Fail-Safe Defaults F10: Save ESC: Exit F1: General Help F7: Optimized Defaults Item Help Menu Level ``` Enter: Select : Move F5: Previous Values - 25 - & DrivingStrengthProfile Options are: Auto (default). & Data Driving Pull-Up Level Options are: Auto (default), +8~-7. Options are: Auto (default), +8~-7. & Cmd Driving Pull-Up Level & Ctrl Driving Pull-Up Level & Clk Driving Pull-Up Level & Data Driving Pull-Down Lev & Cmd Driving Pull-Down Lev & Ctrl Driving Pull-Down Lev & Clk Driving Pull-Down Lev ******** Mother Board Voltage Control ******** >>> CPU & CPU Vcore The default is Auto. & CPU Termination The default is Auto. >>> DRAM & DRAM Voltage The default is Auto. - 26 - 2-4 Standard CMOS Features CMOS Setup Utility-Copyright (C) 1984-2011 Award Software Standard CMOS Features Date (mm:dd:yy) Time (hh:mm:ss) Wed, Nov 30 2011 22:31:24 [None] [None] [None] [None] [All, But Keyboard] 640K 988M 990M Item Help Menu Level ` ` ` ` ` IDE Channel 0 Master IDE Channel 0 Slave IDE Channel 1 Master IDE Channel 1 Slave Halt On Base Memory Extended Memory Total Memory Enter: Select : Move F5: Previous Values +/-/PU/PD: Value F6: Fail-Safe Defaults F10: Save ESC: Exit F1: General Help F7: Optimized Defaults & Date (mm:dd:yy) Sets the system date. Sets the system time. & Time (hh:mm:ss) & IDE Channel 0, 1 Master/Slave IDE Channel 0/1 Master/Slave, Extended IDE Drive Configure your SATA devices by using one of the three methods below: · Auto Lets the BIOS automatically detect SATA devices during the POST. (Default) · None If no SATA devices are used, set this item to None so the system will skip the detection of the device during the POST for faster system startup. · Manual Allows you to manually enter the specifications of the hard drive when the hard drive access mode is set to CHS. (For IDE Channel 0 Master/Slave only. ) Access Mode Sets the hard drive access mode. (Default: Auto) The following fields display your hard drive specifications. If you wish to enter the parameters manually, refer to the information on the hard drive. Capacity Approximate capacity of the currently installed hard drive. Precomp Write precompensation cylinder. [. . . ] The message "PASSWORD DISABLED" will appear, indicating the password has been cancelled. - 36 - 2-14 Save & Exit Setup CMOS Setup Utility-Copyright (C) 1984-2011 Award Software ` ` ` ` ` ` ` MB Intelligent Tweaker(M. I. T. ) PC Health Status ` Standard CMOS Features Load Fail-Safe Defaults Advanced BIOS Features Load Save to CMOS and EXIT (Y/N)?Y Optimized Defaults Advanced Chipset Features Set Supervisor Password Integrated Peripherals Power Management Setup PnP/PCI Configurations : Select Item F10: Save & Exit Setup Save Data to CMOS Set User Password Save & Exit Setup Exit Without Saving F11: Save CMOS to BIOS F12: Load CMOS from BIOS ESC: Quit F8: Q-Flash Press <Enter> on this item and press the <Y> key. This saves the changes to the CMOS and exits the BIOS Setup program. Press <N> or <Esc> to return to the BIOS Setup Main Menu. 2-15 Exit Without Saving CMOS Setup Utility-Copyright (C) 1984-2011 Award Software ` ` ` ` ` ` ` MB Intelligent Tweaker(M. I. T. ) Standard CMOS Features Advanced BIOS Features Advanced Chipset Features Integrated Peripherals Power Management Setup PnP/PCI Configurations PC Health Status Load Fail-Safe Defaults Quit Without Saving (Y/N)?Load Optimized Defaults N Set Supervisor Password Set User Password Save & Exit Setup Exit Without Saving ` : Select Item F10: Save & Exit Setup Abandon all Data F11: Save CMOS to BIOS F12: Load CMOS from BIOS ESC: Quit F8: Q-Flash Press <Enter> on this item and press the <Y> key. [. . . ]