User manual GIGABYTE GO-D1600E

[. . . ] No part of this manual may be reproduced, copied, translated, transmitted, or published in any form or by any means without GIGABYTE's prior written permission. In order to assist in the use of this product, carefully read the User's Manual. For product-related information, check on our website at: http://www. gigabyte. com Identifying Your Motherboard Revision The revision number on your motherboard looks like this: "REV: X. X. " For example, "REV: 1. 0" means the revision of the motherboard is 1. 0. Check your motherboard revision before updating motherboard BIOS, drivers, or when looking for technical information. [. . . ] Unganged Sets memory control mode to two single-channel. (Default) Manual allows all DDR3 Timing items below to be configurable. Options are: Auto (default), 90ns, 110ns, 160ns, 300ns, 350ns. Options are: Auto (default), 90ns, 110ns, 160ns, 300ns, 350ns. - 24 - & 1T/2T Command Timing & CAS# latency & RAS to CAS R/W Delay & Row Precharge Time & Minimum RAS Active Time & TwTr Command Delay & Trfc0 for DIMM1 & Trfc1 for DIMM2 & Write Recovery Time & Precharge Time Options are: Auto (default), 5T~8T, 10T, 12T, 14T, 16T. Options are: Auto (default), 1T~9T. & Row Cycle Time & RAS to RAS Delay & Channel Interleaving & Bank Interleaving Enables or disables memory channel interleaving. Enabled allows the system to simultaneously access different channels of the memory to increase memory performance and stability. (Default: Enabled) Enables or disables memory bank interleaving. Enabled allows the system to simultaneously access different banks of the memory to increase memory performance and stability. (Default: Enabled) Enables or disables memory DQS training each time the system restarts. (Default: Skip DQS) Determines whether to enable memory clock tri-stating in CPU C3 or Alt VID mode. (Default) · Manual Allows you to manually enter the specifications of the hard drive when the hard drive access mode is set to CHS. Access Mode Sets the hard drive access mode. Options are: Auto (default), CHS, LBA, Large. Extended IDE Drive Configure your SATA devices by using one of the two methods below: · Auto Lets the BIOS automatically detect IDE/SATA devices during the POST. (Default) · None If no IDE/SATA devices are used, set this item to None so the system will skip the detection of the device during the POST for faster system startup. Access Mode Sets the hard drive access mode. Capacity Approximate capacity of the currently installed hard drive. - 26 - & Halt On & Memory Allows you to determine whether the system will stop for an error during the POST. Options are: "All Errors, " "No Errors, " "All, But Keyboard". (Default) These fields are read-only and are determined by the BIOS POST. 2-5 Advanced BIOS Features CMOS Setup Utility-Copyright (C) 1984-2011 Award Software Advanced BIOS Features [Press Enter] [Auto] [Disabled] [Auto] [Auto] [Disabled] [Auto] Enabled Enabled Enabled Enabled Enabled Enabled [Press Enter] [Auto] [Hard Disk] [CDROM] [USB-HDD] [Setup] +/-/PU/PD: Value F6: Fail-Safe Defaults F10: Save Item Help Menu Level ` ` IGX Configuration AMD C1E Support Virtualization AMD K8 Cool&Quiet control AMD APM Master Mode CPU Unlock (Note) CPU core Control x CPU core 0(Note) x CPU core 1(Note) x CPU core 2(Note) x CPU core 3(Note) x CPU core 4(Note) x CPU core 5(Note) ` Hard Disk Boot Priority EFI CD/DVD Boot Option First Boot Device Second Boot Device Third Boot Device Password Check Enter: Select : Move F5: Previous Values ESC: Exit F1: General Help F7: Optimized Defaults CMOS Setup Utility-Copyright (C) 1984-2011 Award Software Advanced BIOS Features HDD S. M. A. R. T. Capability Away Mode Full Screen LOGO Show Backup BIOS Image to HDD Init Display First [Disabled] [Disabled] [Enabled] [Disabled] [PCI Slot] Item Help Menu Level ` Enter: Select : Move F5: Previous Values +/-/PU/PD: Value F6: Fail-Safe Defaults F10: Save ESC: Exit F1: General Help F7: Optimized Defaults (Note) This item is present only when you install a CPU that supports this feature. [. . . ] After the creation is complete, the screen will return to LD View Menu where you will see the newlycreated array. Press <Esc> to return to Main Menu and press <Esc> again if you want to exit the RAID BIOS utility. - 39 - Making a SATA RAID Driver Diskette Before installing Windows XP, connect a USB floppy disk drive to your computer first because you need to install the SATA RAID/AHCI driver from a floppy disk that contains the driver during the OS installation. To copy the RAID driver for Windows XP, copy all files in the \BootDrv\SBxxx\x86 folder in the motherboard driver disk to your floppy disk. (To install Windows 64-bit, copy the files in the x64 folder. ) Installing the SATA RAID Driver and Operating System A. [. . . ]