User manual GIGABYTE GS-R22PFL

[. . . ] For detailed product information, carefully read the Serice Guide. For product-related information, check on our website at: http://www. gigabyte. com Preface Before using this information and the product it supports, please read the following general information. This Service Guide provides you with all technical information relating to the BASIC CONFIGURATION decided for GIGABYTE's "global" product offering. To better fit local marketrequirements and enhance product competitiveness, your regional office MAY have decided toextend the functionality of a machine (e. g. add-on card, modem, or extra memory capability). These LOCALIZED FEATURES will NOT be covered in this generic service guide. [. . . ] Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. FCC part 68 (applicable to products fitted with USA modems) The modem complies with Part 68 of the FCC Rules. On this equipment is a label that contains, amongother information, the FCC registration number and Ringer Equivalence Number (REN) for this equipment. You must, upon request, provide this information to your telephone company. If your telephone equipment causes harm to the telephone network, the Telephone Company maydiscontinue your service temporarily. If possible, they will notify in advance. But, if advance notice is notpractical, you will be notified as soon as possible. You will be informed of your right to file a complaint with the FCC. Your telephone company may make changes in its facilities, equipment, operations, or procedures thatcould affect proper operation of your equipment. If they do, you will be notified in advance to give you anopportunity to maintain uninterrupted telephone service. The FCC prohibits this equipment to be connected to party lines or coin-telephone service. The FCC also requires the transmitter of a FAX transmission be properly identified (per FCC Rules Part68, Sec. 68. 381 (c) (3). / for Canadian users only Canadian Department of Communications Compliance Statement This digital apparatus does not exceed the Class A limits for radio noise emissions from digitalapparatus as set out in the radio interference regulations of Industry Canada. Le present appareil numerique n'emet pas de bruits radioelectriques depassant les limites applicables auxappareils numeriques de Classe A prescrites dans le reglement sur le brouillage radioelectrique edicte parIndustrie Canada. DOC notice (for products fitted with an Industry Canada-compliant modem) The Canadian Department of Communications label identifies certified equipment. This certificationmeans that the equipment meets certain telecommunications network protective, operational and safetyrequirements. The Department does not guarantee the equipment will operate to the user satisfaction. Before installing this equipment, users ensure that it is permissible to be connected to the facilities of thelocal Telecommunications Company. The equipment must also be installed using an acceptable methodof connection. The customer should be aware that compliance with the above conditions might not preventdegradation of service in some situations. Repairs to certified equipment should be made by an authorized Canadian maintenance -7- facility designatedby the supplier. · Place the system unit on a flat and stable surface. · Open the system according to the instructions. Failure to properly turn off the server before you start installing componentsmay causeserious damage. Do not attempt the procedures described in the following sections unless youare a qualified servicetechnician. Follow these instructions to install the CPU: 1. Raise the metal locking lever on the socket. Push down the indentation located at the side of the back chassis and slide toward to remove the back chassis cover. Hardware Installation - 14 - 2-3 1. 3. Installing the Heat Sink Apply thermal compound evenly on the top of the CPU. Remove the protective cover from the underside of the heat sink. Place the heat sink(s) on top of the CPU and tighten the four positioning screws. Follow these instructions to install the heat sinks: - 15 - Hardware Installation 2-4 Installing the Memory Read the following guidelines before you begin to install the memory: · Make sure that the motherboard supports the memory. It is recommended that memory of the same capacity, brand, speed, and chips be used. · Always turn off the computer and unplug the power cord from the power outlet before installing the memory to prevent hardware damage. · Memory modules have a foolproof design. [. . . ] Lift up to remove the fan duct To install the fan duct, align the fan duct with the guiding groove. Push down the fan duct into chassis until its firmly seats - 21 - Hardware Installation 2-8 Follow these instructions to replace the fan assembly: 1. Remove thefan assemble pulling the rear edge in the direction of the arrow. Lift up the fan assembly from the chassis. [. . . ]