User manual GIGABYTE GS-R22PHL

[. . . ] 8 Chapter 1 Features Summary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 Chapter 2 System Hardware Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 Step 2-1: Chassis Removal and Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 Step 2-2: CPU Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] Step 2 Lift the riser bracket slightly, then pull it out from the server chassis. Step 3 Unlock the screw on the riser bracket to remove the PCI bracket. Align the expansion card with the guiding groove. Slide the expansion card into the slot until the card firmly seats. Step 4 Reverse step 1 to 3 to reinstall riser bracket into the system module. 3 1 2 3 15 Hardware Installation Process Step 2-6: Hard Disk Drive Installation Step 1 Press the release button. Step 2 Pull the blank out of the drive bay. Step 5 Slide the blank into the bay until it locks into place. Connect cable and power. 1 2 3 4 4 4 4 16 Hardware Installation Process Step 2-7: FAN Duct Removal and Installation Step 1 Pull up the cabled and align the fan duct with the guiding groove. Push down the fan duct into system ntil the its firmly seats. Step 2 Please push the cables into the gap between fan duct and power supply. 1 Guiding groove 17 GS-R22PHL Rack Mount Server Chapter 3 Appearance of GS-R22PHL 3-1: Front View of GS-R22PHL Standard DVD-COMBO Hot-Swap SATA HDDs USB connectors VGA port Front panel switch and LEDs 18 System Appearance 3-2: Rear View of GS-R22PHL Power Mouse connector Keyboard connector COM port VGA port USB connectors RJ45 LAN ports Low-profile riser slot Full-height riser slot 19 GS-R22PHL Rack Mount Server 3-3: Switch and LED Indicators Introduction LAN1/2 LED 1 ID LED ID Switch ID NMI Power Button ID 2 HDD NMI Error Name Power Color Green Green -Green -Blue Condition On Blink Off Blink Off On Off On Off Description Power On Sleep (S1) Power Off (S4/S5) Hard Disk Drive Access No Access and No HDD Fault Unti selected for identification No identification IPMI shows the event log. No event log in IPMI HDD ID (Identification) -Yellow Error - 20 System Appearance 3-4: LAN LED Description Name LAN Color Green - Condition ON BLINK OFF ON BLINK ON BLINK OFF Description LAN Link / no Access LAN Access Idle 1Gbps connection Port identification with 1Gbps connection 100Mbps connection Port identification with 10 or 100Mbps connection 10Mbps connection Link/Activity Green GbE LAN Yellow Speed Yellow Green Green - 21 GS-R22PHL Rack Mount Server 3-5: Connector Icon Description Suggest Icon Description Keyboard Mouse VGA COM LAN USB 22 Motherboard Layout Chapter 4 Motherboard Jumper Setting 4-1: GA-7NCSV1-RH Motherboard Jumper Setting 2 3 4 5 1 8 6 7 1. Set the System Time (HH:MM:SS) System Time Set the System Date. Note that the "Day" automatically changed after you set the date. (Weekend: DD: MM: YY) (YY: 1099~2099) 29 GS-R22PHL Rack Mount Server SATA Port 1/2/3 The category identifies the types of Serial SATA hard disk from drive 1 to 6 that has been installed in the computer. System will automatically detect HDD type. Note that the specifications of your drive must match with the drive table. The hard disk will not work properly if you enter improper information for this category. Hard drive information should be labled on the outside device casing. Enter the appropriate option based on this information. (Default setting) CD-ROM: Use for ATAPI CD-ROM drives or double click [Auto] to set all HDD parameters automatically. ATAPI Removable: Removable disk drive is installed here. Multi-Sector Transfer This field displays the information of Multi-Sector Transfer Mode. [. . . ] Including information of BIOS Version, GBIA Module Version, BMC Firmware Revision, and SDR Revision. BMC Command Line Interface Enabled Disabled Enable BMC Command Line Interface. (Default setting) Event Log Confuguration This option contains additional setup menu to configure the Event Log Configuration. Clear all Event Logs Enter The system event log will be cleared if pressing Enter. Address obtained by BMC running DHCP address. [. . . ]