User manual GIGABYTE GS-SR157L

[. . . ] GS-SR157L 1U Rack Mount Server System Installation Guide Intel® Pentium Prescot LGA775 Processor Serverboard Rev. 1001 25A080-0157L-F00 GS-SR157L Rack Mount Server Table of Content Safety, Care and Regulatory Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Contents Packages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] Step 2 Lift the riser bracket slightly, then pull it out from the server chassis. Step 3 Align the expansion card with the guiding groove. Slide the expansion card into the slot until the card firmly seats. Step 4 Align the riser bracket to the system module (see the arrow direction mark 1), and push it to locked position. Step 5 Reverse Step 1 & 2 to lock the riser bracket firmly. Installation completed. Step 1 Step 2 Step 3 Step 4 15 GS-SR157L Rack Mount Server Step 3-6: Hard Disk Drive Installation Step 1 Lossen the screws securing the hard drive plate. Step 2 Slide toward to remove the hard drive plate from system. Step 3 Place hard disk on the plate and lock hard drive with 4 screws. Step 4 Replace the hard drive plate, slide the blank into the bay until it locks into place. Connect HDD power cable. Step 5 Reverse step 1, 2, 3 and 4 to complete the HDD installtion. Step 1 Step 2 Remove Step 3 Step 4 16 Hardware Installation Process Step 3-7: FAN Duct Removal and Installation Step 1 Pull up the screw-holder and lossen the thumbscrews. Step 2 For FAN Duct Installation, place the fan duct on the top of heat sinks. Fasten the screws to the locked position and push down the screw-holders. Step 1 Step 2 17 GS-SR157L Rack Mount Server Chapter 4 Appearance of GS-SR157L 4-1: Front View of GS-SR157L Slim Type CD-ROM Standard Floopy USB Connector LE D s RJ45 (For Console Redirection) 18 System Appearance 4-2: Rear View of GS-SR157L Po we r VGA Po rt COM Po rt Lo w Pro file Rise r Slo t Full-size /Full-le ng th Rise r Slo t Ke yb o ard Co nne cto r Mo use Co nne cto r USB Co nne cto rs LAN 1 & 2 Po rts 19 GS-SR157L Rack Mount Server 4-3: Switch and LED Indicators Introduction Status HDD Fail Warning HDD Power/Sleep ID Name Power Color Green Green -Status Green Amber Amber Condition On Blink Off On Blink On NMI LAN1/2 Activities Description Power On Sleep (S1) Power Off (S4/S5) System Ready On/ Alarm System Ready but deqraded, CPU Failed, DIMM Killed. Critical Alarm: Critical Power Module Failure, Critical FANs Failure, Voltage (Power Supply) Critical Temperature and Voltage -HDD Green Amber -Green Green -Green Green -Blue -- Off Blink On Off On Blink Off On Blink Off Blink Off 20 System Not Ready/ Post error/NMI event/CPU or terminator missing Hard Disk Drive Access HDD Fault No Access and No HDD Fault LAN Link / No access LAN access Idle LAN Link / No access LAN access Idle Unit selected for identification No identification LAN1 Activity LAN2 Activity Identification LED Description 4-4: LAN LED Description Name LAN Color Green Condition ON BLINK OFF ON BLINK ON BLINK OFF Description LAN Link / no Access LAN Access Idle 1Gbps connection Port identification with 1Gbps connection 100Mbps connection Port identification with 10 or 100Mbps connection 10Mbps connection Link/Activity Green GbE LAN Yellow Speed Yellow Green Green - 21 GS-SR157L Rack Mount Server 4-5 : Connector Icon Description Suggest Icon Description Keyboard VGA Mouse LA N Parallel Port Serial Port USB 22 Motherboard Layout Chapter 5 Motherboard Layout & Jumper Setting 5-1: GA-8ICXR Motherboard Layout O PQ M M L 12 4 C D 8 X J I H G 3 W V N U T R F S A 5 6 7 K E B Y Z 23 GS-SR157L Rack Mount Server A B C D E F G H I J K L M N O P Q R S T U V W X Y Z CPU LGA775 Intel MCH E7221 Intel 6702 PXH-V IntelICH6R FDD IDE1 SATA1 SATA2 SATA3 SATA4 Front Panel IPMBI Intel 82541PI USB2 COM2 WOR WOL FAN1 FAN2 FAN3 FAN4 FAN5 FAN6 FAN7 ATX1 ATX 12V 1 2 3 4 5 6 7 8 IPMB1 IPMB2 PCI1 PCI_X1 DDR1 DDR2 DDR3 DDR4 24 Jumper Setting 5-2: Jumper Setting CLR_CMOS ( (Clear CMOS Function) You may clear the CMOS data to its default values by this jumper. Default value doesn't include the "Shunter" to prevent from improper use this jumper. To clear CMOS, temporarily short 1-2 pin. 1 1 1-2 close: Clear CMOS 2-3 close: Normal (Default value) 25 GS-SR157L Rack Mount Server Chapter 6 BIOS Setup BIOS Setup is an overview of the BIOS Setup Program. The program that allows users to modify the basic system configuration. This type of information is stored in battery-backed CMOS RAM so that it retains the Setup information when the power is turned off. ENTERINGSETUP Power ON the computer and press <F2> immediately will allow you to enter Setup. CONTROLKEYS <> <> < < > > Move to previous item Move to next item Move to the item in the left hand Move to the item in the right hand Main Menu - Quit and not save changes into CMOS Status Page Setup Menu and Option Page Setup Menu - Exit current page and return to Main Menu <+/PgUp> Increase the numeric value or make changes <-/PgDn> <F1> <F2> <F3> <F4> <F6> <F7> <F8> <F9> <F10> Decrease the numeric value or make changes General help, only for Status Page Setup Menu and Option Page Setup Menu Reserved Reserved Reserved Reserved Reserved Reserved Load the Optimized Defaults Save all the CMOS changes, only for Main Menu <Esc> 26 BIOS Setup GETTINGHELP Main Menu The on-line description of the highlighted setup function is displayed at the bottom of the screen. Status Page Setup Menu / Option Page Setup Menu Press F1 to pop up a small help window that describes the appropriate keys to use and the possible selections for the highlighted item. To exit the Help Window press <Esc>. Main This setup page includes all the items in standard compatible BIOS. Advanced This setup page includes all the items of AMI special enhanced features. (ex: Auto detect fan and temperature status, automatically configure hard disk parameters. ) Security Change, set, or disable password. It allows you to limit access the system and setup. Server Server additional features enabled/disabled setup menus. Boot This setup page include all the items of first boot function features. Exit There are five optionsin this selection: Exit Saving Changes, Exit Discarding Changes, Load Optimal Defaults, Load Failsafe Defaults, and Discard Changes. 27 GS-SR157L Rack Mount Server Main Once you enter Phoenix BIOS Setup Utility, the Main Menu (Figure 1) will appear on the screen. Use arrow keys to select among the items and press <Enter> to accept or enter the sub-menu. Figure 1: Main System Time The time is calculated based on the 24-hour military time clock. Set the System Time (HH:MM:SS) System Date Set the System Date. [. . . ] Power On Stay Off Last State System power state when AC cord is re-plugged. Do not power on system when AC power is back. Set system to the last sate when AC power is removed. Do not power on system when AC power is back. [. . . ]