User manual GIGABYTE GZ-X6

[. . . ] Be sure to observe the instructions in the installation manual. 02 English Content 1. Components Introduction 1-1 Casing's Internal Structure 1-2 Casing's Panel Structure 1-3 Removal of Side and Front Panels 2. Installation Instruction 4-1 Installation of Power Supply 4-2 Installation of Motherboard 4-3 Installation of Add-On card 4-4 Installation of Front Multi-Media I/O Ports 4-5 Connection of Fan Power Cable 4-6 Installation of 5. 25" Front Device Bay 4-7 Installation of 3. 5" Front Device Bay 4-8 Installation of 3. 5" Internal Device Bay 4-9 Application of Removable/Dual Directional HDD Rack 4-10 Installation of 2. 5" Enclosure 4-11 Application of DIY inter changeable LED lighting 4-12 Application of Security locks 4-13 Application of Foot Support 4-14 Application of Liquid Cooling System 4-15 Recommended GIGABYTE Thermal Solution products 04 04 05 05 06 07 08 08 08 08 09 10 10 10 10 11 11 11 11 12 12 12 English 03 1. Components Introduction 1-1 Casing's Internal Structure Power Supply Bay 5. 25" Front Device Bay Dual Rear fans Motherboard tray and PCI Slot panel 3. 5" Front Device Bay PCI Tool-Free Fastener 3. 5" Internal Device Bay Piping Outlets Front intake Fan Foot Support Accessory Box (Refer to the figures below for the attachments in the accessory box) Copper Stand Off x 11 Motherboard Securing Screw x 12 Power Supply Securing screw x 4 3. 5" Device Thumbscrews x8 Blue Led 2. 5" HDD mobile enclosure protective carry bag USB Y Cable Wire Clamp x 2 Key Cable tie x 2 04 English Cable Kit (Refer to the figures below for the cable connectors) eSATA USB 2. 0 Audio (HD & AC'97) IEEE1394 (Multi-connectors) Fan 3-Pin Connector Power LED 4-pin Connector Power SW / Reset SW / Speaker Connector 1-2 Casing's Panel Structure Red Led Disc Storage 2. 5" enclosure docking Latch / Security Lock Transparent side panel Ventilated mesh side panel Power Switch Multi-Media I/O port 1-3 Removal of Side and Front Panels 1-3. 1 To remove side panels: 1-3. 1a. [. . . ] Remove the 6 thumb screws at the rear of the side panel, and detach the side panels. 1-3. 2 To remove front panel: 1-3. 2a. Remove the left and right side panels (see step 1-3. 1 on page 5), release the 6 clamps that hold the front panel onto the chassis. English 05 2. Features - High quality Design GIGABYTE top-class Full tower thermal solution casing. Aluminum 3D front panel design with hair-line brush anodized finishing. Illuminated and atmospherically-soothing backlight for a post-modern classy impression. - Complete I/O Support Complete Top panel multi-media support, includes 1 x eSATA, 2 x USB 2. 0, 1 x IEEE1394, 1 x Audio Set (HD & AC'97). Full Support of GIGABYTE thermal solution LCS and Air cooling products lines. Supports E-ATX / CEB / ATX / Micro ATX motherboards. - Integration of Cooling Technology Industry leading dual rear 12cm silent blue LED fan, Large air volume with low noise. Unique ventilated mesh / transparent side panel design. - Convenience of assembly Scratch-resistant processing that ensures safety during assembly. Side panel with one-hand-operation, for easy disassembly. 4-3. 2 4-3. 3 4-3. 4 4-3. 1 08 English 4-4 Installation of Front Multi-Media I/O Ports Incorrect connection of sockets can cause the motherboard to malfunction or completely destroy the motherboard. Please observe the installation instructions in the manual carefully as incorrect installations or connection causing faults will void your warranty. The top panel includes: (1) 1 x eSATA, 2 x USB 2. 0, 1 x IEEE 1394 and 1 x Audio Set (HD or AC'97) (2) Basic casing power switch control cable kit Required Tools: None Please refer to the instructions supplied by the motherboard manufacturer and make sure the correct type of connector is used prior to installation. (1) 1 x eSATA, 2 x USB 2. 0, 1 x IEEE 1394 and 1 x Audio Set (HD or AC'97) 4-4. 1 Insert the eSATA connector into the corresponding socket on the motherboard. 4-4. 2 Insert the USB 2. 0 connectors into the corresponding sockets on the motherboard (please refer to the motherboard user manual for further information). USB 2. 0 connector Pin 1 2 3 4 5 Definition Power Power USB DxUSB DyUSB Dx+ Pin 6 7 8 9 10 USB Over current Definition USB Dy+ GND GND 4-4. 3 Insert the IEEE 1394 connector into the corresponding socket on the motherboard. IEEE 1394 connector A Pin 1 2 3 4 5 Definition TPA+ TPAGND GND TPB+ Definition TPA+ TPAGND GND TPB+ Pin 6 7 8 9 10 Pin 6 7 8 9 10 GND +12V +12V GND Definition TPB+12V +12V Definition TPB- B A IEEE 1394 connector C C Pin 1 2 3 4 5 6 7 8 Definition +12V +12V TPA+ TPAGND GND TPB+ TPBPin 9 10 11 12 13 14 15 16 TPB1+ TPB1Definition +12V +12V TPA1+ TPA1GND IEEE 1394 connector B Pin 1 2 3 4 5 4-4. 4 Insert the Audio connector into the corresponding socket on the motherboard. HD AUDIO Pin 1 2 3 4 5 Definition MIC2_L GND MIC2_R -ACZ_DET LINE2_R Definition MIC GND MIC Power NC Line Out(R) Pin 6 7 8 9 10 Pin 6 7 8 9 10 Line Out(L) NC LINE2_L FSENSE2 Definition NC NC Definition FSENSE1 FAUDIO_JD AC'97 Pin 1 2 3 4 5 English 09 (2) Basic casing power switch control cable kit Follow the connectors list below for installation (see figure below) Connector Power LED Power SW Color Green(+) / Wite(-) Orange(+) / White(-) 4-5 Connection of Fan Power Cable This chassis has 1 x 12cm silent cooling fan at the front and 2 x 12 cm silent blue LED fans at the rear. There are internal connectors that connect the front and rear fans making it into a single 3-pin power connector. Required Tools: None 4-5. 1 Insert the 3-pin connector into the system fan power connector on the motherboard. Different Motherboards have different installation areas, specifications, screw holes and connectors. Please read the motherboard user manual supplied by the motherboard manufacturer. 4-6 Installation of 5. 25" Front Device Bay 4-6-1 Open the front panel door and side panel, remove the plastic bezel and EMI plate through the inside of the chassis. 4-6-2 Slide-in the 5. 25" device through the front panel to align it with the front panel bezels. 4-6-3 Secure the 5. 25" device with the internal latch. Refer to the figure for installation procedure. 4-6-4 Installation complete. 4-6. 1 4-6. 2 4-6. 3 LOCK 4-6. 4 4-7 Installation of 3. 5" Front Device Bay The Installation of the 3. 5" front device is the same as the installation of the 5. 25" front devices. Please refer to step 4-6. Required parts: none 4-8 Installation of 3. 5" Internal Device Bay This chassis provides a removable/dual directional HDD rack to accommodate up to 5 hard disc drives. Required Tools: Thumbscrews (4 per hard disc drive) 4-8. 1 4-8. 2 Slide the HDD into the rack and secure the HDD with the thumbscrews. 10 English 4-9 Application of Removable/Dual Directional HDD Rack This chassis includes a removable/dual directional HDD rack for preferred installation direction and optimal heat dissipation. Required Tools: None 4-9. 1 4-9. 2 Remove the thumbscrew that secures the removable HDD rack. Unlock tool-free fastener of the removable HDD rack by pushing it downwards. 4-9. 3 A A B B Change the HDD rack directional alternating fastener on top of the rack and align the arrows for desired direction. [. . . ] 4-6-4 Installation complete. 4-6. 1 4-6. 2 4-6. 3 LOCK 4-6. 4 4-7 Installation of 3. 5" Front Device Bay The Installation of the 3. 5" front device is the same as the installation of the 5. 25" front devices. Please refer to step 4-6. Required parts: none 4-8 Installation of 3. 5" Internal Device Bay This chassis provides a removable/dual directional HDD rack to accommodate up to 5 hard disc drives. Required Tools: Thumbscrews (4 per hard disc drive) 4-8. 1 4-8. 2 Slide the HDD into the rack and secure the HDD with the thumbscrews. 10 English 4-9 Application of Removable/Dual Directional HDD Rack This chassis includes a removable/dual directional HDD rack for preferred installation direction and optimal heat dissipation. Required Tools: None 4-9. 1 4-9. 2 Remove the thumbscrew that secures the removable HDD rack. Unlock tool-free fastener of the removable HDD rack by pushing it downwards. 4-9. 3 A A B B Change the HDD rack directional alternating fastener on top of the rack and align the arrows for desired direction. (Dual Direction Only) 4-10 Installation of 2. 5" Enclosure 4-10. 1 Connect the 4-pin power cable to the 5. 25" front device housing 4-pin power port. 4-10. 2 Connect the SATA cable from the e-SATA side to the SATA port on the motherboard. [. . . ]