User manual GIGAFAST EE102-AEX

[. . . ] CardBus 10/100M Ethernet card User Manual Version 1. 2 Regulatory compliance This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC Rules. This equipment also complies with CE EN55022 Class B and VCCI V3 Class B specifications. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. [. . . ] Windows 98 copies files to your hard disk drive, and you see the following screen: 8. Click Finish. Note! Windows 98 may need to copy required system files and will prompt you 16 Win 95/98/2000/ME/NT to input the path to the files. Click Finish. Note! Windows ME may need to copy required system files and will prompt you to input the path to the files. Follow the instructions on your screen, then click OK to continue. You should reboot your system to finish the installation. 23 CardBus Ethernet card user manual Driver installation for Windows NT 4. 0 This installation procedure assumes that you have installed the network component on your computer. To check whether the network component has been installed, double click the Network icon in the Control Panel. If it has not been installed, refer to the Windows NT 4. 0 installation guide for instructions on installing the component. Follow the steps below to install the driver. Insert the CardBus Ethernet card into an available CardBus slot on your notebook 2. Log in to NT 4. 0 as ¡Administrator¡¨ 3. Double click the Network icon in the Control Panel, and select the Adapters tab as shown in the following screen: 24 Win 95/98/2000/ME/NT 4. Type ¡A:\WinNT40¡¨ w here A Insert the driver disk, and click OK. After finding the installation file, the Select OEM Option window is displayed. 25 CardBus Ethernet card user manual 7. A screens appears prompting you to input the IRQ, I/O port address, and connection type: 8. Select the desired resources and connection type. Note! You must select resources that are not being used by another device; otherwise, you will have a system conflict error. In case of a system conflict error, try another setting and continue. 9. Windows will configure the CardBus Ethernet card. You are returned to the Network window. 26 Win 95/98/2000/ME/NT 10. Windows NT 4. 0 will bind the adapter with the network component and you will be prompted to restart the system. When Windows NT is finished binding the adapter to the network component, you are prompted to restart the system. Click Yes to finish the installation. 27 Chapter 4 Driver installation for DOS environments This section covers CardBus 10/100Mbps Ethernet Card driver installation for DOS environment operating systems. System Requirements Hardware Requirements Notebook equipped with Type II PC Card slot and CardBus controller (PCMCIA 1995 PC Card Standard or higher) The Card & Socket service drivers should comply with PCMCIA 1995 PC Card Standard or higher Software Requirements Driver installation You must install the CardBus 10/100Mbps Ethernet Card drivers before your computer system can recognize your Ethernet Card. The following sections cover client driver installation. Driver installation program INSTALL is the CardBus 10/100Mbps Ethernet Card driver installation program. The INSTALL program automatically selects the 28 Driver installation for DOS environments most suitable option settings, or you can perform a custom configuration where you individually select each setting. Quick installation This section gives a brief overview of the installation process. [. . . ] When the install program prompts you for the manufacturer's driver disk in the Enter NDIS driver directory screen, insert the driver disk. Follow the instructions on the screen to complete the installation, then reboot the computer to start LANtastic. 40 Installation for LINUX Chapter 5 Installation for LINUX This device driver has been fully tested on the following platforms: Slackware 3. 6 Slackware 4. 0 Slackware 7. 0 Slackware 7. 1 Redhat 5. 2 Redhat 6. 0 Redhat 6. 2 The complete file list is as follows: README makefile rtl8139. c en0100r. o Before Installation Before you start rebuilding the driver, you must have PCMCIA binaries and source installed in your system. PCMCIA module version 3. 0. 9 or later are quaranteed to work well with this driver. Latest version of PCMCIA module is available at ftp://sourceforge. com. [. . . ]