User manual GIGAFAST PE904-R

[. . . ] GigaFast HomePlug Broadband Internet Router PE904-R User Manual GigaFast Copyright The contents of this publication may not be reproduced in any part or as a whole, stored, transcribed in an information retrieval system, translated into any language, or transmitted in any form or by any means, mechanical, magnetic, electronic, optical, photocopying, manual, or otherwise, without the prior written permission. Trademarks All products, company, brand names are trademarks or registered trademarks of their respective companies. They are used for identification purpose only. Specifications are subject to be changed without prior notice. Copyright© 2004, Gigafast Inc. , All Right Reserved 2 GigaFast FCC Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against radio interference in a commercial environment. [. . . ] Some users might have trouble getting the router to communicate with their game console servers (i. e. PlayStation2 by Sony or Xbox by Microsoft) and if that is the case then enable DMZ and it should allow you to enter the server after save & restart. Section 7 ­ Auto 2-Way Application This section can let a user open certain service ports for software. Because there is much internet software need 2-way access right and they open many TCP/UDP ports simultaneously such as online game or audio/video conference, they always connect to an outside server with a fixed destination port. Then the server would communicate with the application in LAN by using a predefined incoming port or a specific range of incoming ports. If a user has trouble playing certain games and the games require a port to be opened, then Auto 2-Way Application is the place to enable ports for it. Chapter 4 43 GigaFast Auto 2-Way Application ­ Once enabled, put the outgoing port in the `Trigger Port' box and incoming port in the `Incoming Port'. All software, games have its ports to be opened. Obtain the port numbers and enter them under this section will allow the user to join any particular server without being kicked or timed out. Please go to your software website to obtain the service port information for your software. Once a trigger is occupied, the second or later LAN PC should not use that trigger port until the first LAN PC has released it. Release means that the first PC doesn't use that trigger port for more then 5-6 minutes. By default this option is set at `Disable'. Chapter 4 44 GigaFast Section 8 ­ Dynamic DNS This option will automatically translate your domain name to your WAN IP address for others to access your page. Dynamic DNS ­ If you don't have a domain name and a host setup then others will require a Dynamic DNS to log onto your webpage. This enables others to see you on the WAN side and allows them to browse your own page. Often the server will automatically update your WAN IP address, therefore the Dynamic DNS function allow the update to be saved so others can still browse your page without the changes to be made manually. For further information please visit: www. DynDNS. org and by default this function is set at `Disable'. Chapter 4 45 GigaFast Conclusion This concludes the Basic & Advance Configuration for the PE904-R. The most common questions are answered based on these two chapters. If you need further assistance or perhaps require more information then please visit our FAQ guide or contact one of our lines listed below. Appendix A: Cabling and Pin Assignment A-1 RJ-45 There are different grades, or categories, of twisted-pair cabling. Category 5 is the most reliable and is highly recommended. Straightthrough cables are used for connecting computers' NIC cards to a hub. Crossover cables are used for connecting a hub to another hub. (The router provides a built-in uplink/normal switch. Uplink mode is crossed internally, which allows you to link or connect hubs together with a straight-through cable instead. ) A-1-1 RJ-45 pin assignment There are 8 thin, color-coded wires inside, run from one end of the cable to the other. [. . . ] ("GFE") warrants its products to be free from defects in workmanship and materials, under normal use and service, for the applicable warranty term. All GFE products carry a standard limited warranty from the date of purchase from GFE or its Authorized Reseller. GFE may, at its own discretion, repair or replace any product not operating as warranted with a similar or functionally equivalent product, during the applicable warranty term. All products that are replaced become the property of GFE. [. . . ]