User manual GOVIDEO R6540 Product Manual

[. . . ] Unpack Your DVD Recorder · · · · · · · · · R6540 DVD recorder (1) Remote control (1) 1. 5V AAA alkaline batteries (2) Audio/video cable (1) RF (Antenna) cable (1) User's guide (1) Quick reference guide (1) Warranty registration card (1) DVD+RW disc (1) Insert Remote Control Batteries 1 Remove battery cover on back of remote control. 2 Insert two 1. 5V AAA batteries, paying attention to the correct polarities (+/-). In case warranty service is required, please take a moment to attach your receipt to this manual and write down your Serial Number, located on the back panel of the DVD Recorder: __________________________________. R6540 DVD Recorder © 2004. "Dolby", "Pro Logic", and the double D symbol are trademarks of Dolby Laboratories. [. . . ] max per disc, comparable to DVD quality) · SP - Select for Standard Play mode (2 hrs. max per disc) · LP - Select for Long Play mode (3 hrs. max per disc, comparable to S-VHS quality) · EP - Select for Extended Play mode (4 hrs. max per disc) · SLP - Select for Super Long Play mode (6 hrs. max per disc, comparable to standard VHS quality). Enable Timer Recording · Use the / buttons to turn the selected event On or Off. · This allows you to save unused Timer Recording settings for future use. R6540 DVD Recorder 9 Press Setup to save your settings and exit the Setup menu. · The unit will alert you if you have entered any invalid data in your Timer Recording settings. · The unit will also alert you if you have entered overlapping events. · To edit an event, simply select it and press Play /Enter. · To delete an entry, press Clear. 10 Press On/Standby on the remote control to put the R6540 in Standby mode. 11 When the starting time for the recording is reached, the unit will automatically begin recording according to your settings. · To stop a Timer Recording in progress, simply press the On/Standby button on the remote control. · If you press the Stop button during a Timer Recording, you will be instructed to press the On/Standby button. 30 Chapter 4 :: Basic Disc Playback DVD Playback Basic Setup Getting Started Playing a DVD Before you begin: · Turn on the DVD player using the front panel Power button. If the unit is in Standby mode, press On/Standby on the remote control to power on the unit. The green Power indicator will glow on the front panel display. · Turn on your TV, and set it to the video input connected to the DVD player. · Turn on your audio system (if using an external amplifier/audio system), and set it to the input connected to the DVD player. 1 Press Open/Close on the remote control or front panel to open the disc drawer. 2 Place the disc in the drawer with the label side facing up and playback side facing down. If the disc has two sides, place the disc with the desired playback side facing down. 3 Press Open/Close again to close the disc drawer. [. . . ] To reduce the risk of electric shock, do not remove the unit cover or back. Refer servicing to qualified personnel only. WARNING: TO AVOID HAZARDOUS EXPOSURE TO INVISIBLE LASER RADIATION, DO NOT OPEN OR REMOVE/DEFEAT LASER TRANSPORT PROTECTIVE HOUSING. CLASS 1 LASER PRODUCT This appliance is classified as a CLASS 1 LASER PRODUCT. The CLASS 1 LASER PRODUCT MARKING is located on the rear panel. Note to CATV System Installer This reminder is provided to call the CATV system installer's attention to Article 820-40 of the National Electronic Code that provides guidelines for proper grounding and, in particular, specifies that the cable ground shall be connected to the grounding system of the building, as close to the point of cable entry as practical. 51 Getting Started · If the product does not operate normally by following the operating instructions. Adjust only those controls that are covered by the operating instructions as an improper adjustment of other controls may result in damage and will often require extensive work by a qualified technician to restore the product to its normal operation, · If the product has been dropped or damaged in any way, and · When the product exhibits a distinct change in performance ­ this indicates a need for service. User/Installer Caution Your authority to operate this FCC certified equipment could be voided if you make changes or modifications not expressly approved by the manufacturer, who is responsible for compliance with Part 15 FCC rules. [. . . ]