Lastmanuals offers a socially driven service of sharing, storing and searching manuals related to use of hardware and software : user guide, owner's manual, quick start guide, technical datasheets... DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!
If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Lastmanuals provides you a fast and easy access to the user manual GRACO 15H871. We hope that this GRACO 15H871 user guide will be useful to you.
Lastmanuals help download the user guide GRACO 15H871.
Manual abstract: user guide GRACO 15H871REV 9-2010
Detailed instructions for use are in the User's Guide.
[. . . ] Remove the motor and coupler as follows: a. 1 for NEMA 184/182 TC Frame electric motors. 2 for IEC 112M/B5 or 100L/B5 Frame electric motors. While one person supports the motor (19), remove the screws (37). [. . . ] Hold slider piston (9) flats with 3/4 in. wrench, and brace against tie rod (3).
4 32 CR OS
9
ti9225a
FIG. Remove the two output seals (116) as follows:
10
12
14
ti9223b
a. Place the tool (C) onto the output shaft (OS). (13 mm) screws (G) to lock the tool in place.
FIG. Remove Coupling Nut (Stand Side Shown)
4
311597C
Kit Installation
b.
Drill 1/8 in. (3 mm) diameter (maximum) pilot holes in the seals (116), using the holes for the sheet metal screws (D) as a template. Install the sheet metal screws (D) through the tool and into the seals (116). Tighten screws (D) evenly to pull both seals out.
11. Install the two output seals (116) as follows: a. Place tape over the output shaft keyway, to prevent damage to the new seals. Pack the output shaft seal cavity with Part No. Place one output seal (116) over the output shaft (OS), with the lips facing in. Remove the sheet metal screws from the tool (C). Place the tool (C) onto the output shaft (OS), fitting one screw (A) into the slot of the shaft. Tighten the screws (G) to lock it onto the shaft.
c.
D
OS
c.
G
d. Place the installation tool (E) against the seal (116) as shown. Install the tool cover (F) and evenly tighten the screws (J) to seat the seal on the output shaft (OS).
D G C D 116 f.
ti8964a
Remove the tools. Take three measurements 120° apart, from the surface of the seal to the face of the housing (H). The three measurements must be within . 020 in. If not, repeat steps c through e.
FIG. Remove the tape.
1 4 5
Pack cavity with grease before installing seal. [. . . ] The equipment will be returned to the original purchaser transportation prepaid. If inspection of the equipment does not disclose any defect in material or workmanship, repairs will be made at a reasonable charge, which charges may include the costs of parts, labor, and transportation. THIS WARRANTY IS EXCLUSIVE, AND IS IN LIEU OF ANY OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO WARRANTY OF MERCHANTABILITY OR WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE. Graco's sole obligation and buyer's sole remedy for any breach of warranty shall be as set forth above. [. . . ]
DISCLAIMER TO DOWNLOAD THE USER GUIDE GRACO 15H871
Lastmanuals offers a socially driven service of sharing, storing and searching manuals related to use of hardware and software : user guide, owner's manual, quick start guide, technical datasheets... In any way can't Lastmanuals be held responsible if the document you are looking for is not available, incomplete, in a different language than yours, or if the model or language do not match the description. Lastmanuals, for instance, does not offer a translation service.
Click on "Download the user manual" at the end of this Contract if you accept its terms, the downloading of the manual GRACO 15H871 will begin.
