User manual GRACO H-35 PRO 66942-1

Lastmanuals offers a socially driven service of sharing, storing and searching manuals related to use of hardware and software : user guide, owner's manual, quick start guide, technical datasheets... DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!

If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Lastmanuals provides you a fast and easy access to the user manual GRACO H-35 PRO. We hope that this GRACO H-35 PRO user guide will be useful to you.

Lastmanuals help download the user guide GRACO H-35 PRO.


Mode d'emploi GRACO H-35 PRO
Download
Manual abstract: user guide GRACO H-35 PRO66942-1

Detailed instructions for use are in the User's Guide.

[. . . ] 120 100 80 140 160 180 200 220 120 100 80 140 160 180 200 220 H-20/35 Pro Proportioning Unit Operating Manual 66942-1 March 1, 2005 Issue 3 GUSMER CORPORATION ® One Gusmer Drive Lakewood, New Jersey, USA 08701-8055 Toll Free 1-800-367-4767 (USA & Canada) Phone: (732) 370-9000 Fax: (732) 905-8968 Copyright 2005, GUSMER CORPORATION ® http://www. gusmer. com NOTICE: This manual contains important information about your GUSMER equipment. Read and retain for future reference. H-20/35 Pro Series Proportioning Unit NOTICE: The equipment described in this technical manual must only be operated or serviced by properly trained individuals, thoroughly familiar with the operating instructions and limitations of the equipment. For technical service, call your local distributor. Call: 1-800-FOR-GSMR (1-800-367-4767) for the name and telephone number of your local distributor. NOTICE: All statements, information and data given herein are believed to be accurate and reliable but are presented without guarantee, warranty or responsibility of any kind expressed or implied. [. . . ] (See item 15 on page 10. ) NOTE: The pump switch must be in the RETRACT or NORMAL position to adjust the hydraulic pressure. 14. Check the pressure of each proportioning pump. After setting the pump switch to NORMAL, monitor both pressure gauges. The resin and isocyanate pressures should be approximately equal and the pressures must remain fixed. Set the pump switch to RETRACT and observe the pressures again; they must remain fixed. If the pressure bleeds off on either stroke, see TROUBLESHOOTING, Proportioning System on page 28 before continuing. The proportioning unit is now ready for operation. Consult the spray gun operating manual and test spray as per the directions. Daily Shut-down Procedure 1. Trigger the spray gun off target until the isocyanate proportioning pump stops in the retracted position and the pressure of both pumps bleeds off to a point where the spray pattern begins to diminish. IMPORTANT: DO NOT bleed the pressure to zero, as some pressure is required to keep the packings operating normally and prevent seepage during shutdown. Turn OFF the green hydraulic motor switch. The light within the switch will go out. Turn OFF the green A- and R- heater switches. The lights within the switches will go out. The light within the switch will go out. Turn OFF the amber control power switch. The light within the switch and the temperature controllers should go out. Close both A- and R-inlet supply valves. Coil and store the heated hose in a manner that prevents damage. 5. Shut down the chemical supply system as required. Turn OFF the main air supply to the transfer pumps/day tanks. Shut down and service the spray gun as required (see spray gun operating manual). 24 66942-1, Issue 3 Operating Manual Troubleshooting TROUBLESHOOTING General Information When properly maintained and operated, GUSMER equipment will provide long and faithful service. [. . . ] NOTE: You may send a marked copy of the page as an attachment to your submittal. Name IM Number Issue Number 5 Date of Issue 6 7 Page Number Discrepancy 44 66942-1, Issue 3 H-20/35 ProTM and HV-20/35TM DIGITAL TEMPERATURE CONTROLLER ADDENDUM Starting May 2, 2005 all Graco-Gusmer H-20/35 ProTM and HV-20/35TM Proportioning Units will be equipped with temperature controllers featuring a user-selectable Fahrenheit or Celsius scale display option, enabling you to change between °F and °C temperature displays as desired. All temperature controllers will be factory-set to display in Fahrenheit scale, eliminating the need to distinguish between separate Fahrenheit and Celsius (-C) replacement controllers after this date. The replacement part numbers for all H-20/35 ProTM and HV-20/35TM temperature controllers are as follows: H-20/35 ProTM and HV-20/35TM all: H-20/35 ProTM and HV-20/35TM all: Primary Heater Temperature Controller: Hose Heater Temperature Controller: 6690-26-29-1KIT 6690-26-29-2KIT To change or enter the set point for the new style controller, proceed as follows: WARNING: DO NOT TURN THE TEMPERATURE CONTROLLERS ON UNTIL ALL PURGING PROCEDURES ARE COMPLETED AND THE HEATERS ARE COMPLETELY FILLED WITH CHEMICAL. 1. 2. Make sure the red main disconnect is ON. [. . . ]

DISCLAIMER TO DOWNLOAD THE USER GUIDE GRACO H-35 PRO

Lastmanuals offers a socially driven service of sharing, storing and searching manuals related to use of hardware and software : user guide, owner's manual, quick start guide, technical datasheets...
In any way can't Lastmanuals be held responsible if the document you are looking for is not available, incomplete, in a different language than yours, or if the model or language do not match the description. Lastmanuals, for instance, does not offer a translation service.

Click on "Download the user manual" at the end of this Contract if you accept its terms, the downloading of the manual GRACO H-35 PRO will begin.

Search for a user manual

 

Copyright © 2015 - LastManuals - All Rights Reserved.
Designated trademarks and brands are the property of their respective owners.

flag