User manual GRACO L12415

[. . . ] Modular pump/reservoir design plus built-in features (see below) enable the PH Manual Pump to be customized for a wide range of applications. The PH Manual Pump permits increased standardization with resultant economies in spare parts stocking and greater employee familiarity with plant or job site lubrication systems. This pump is sturdily built with aluminum and steel components to meet the high standards of performance and quality you expect from Graco® products. Even with an integrally mounted 20-pint or 20-pound capacity reservoir and bottom-mounted optional outlet valve, it stands only 27. 84 inches (70. 7 cm) high, is 7. 25 inches (18. 4 cm) wide and 11. 03 inches (28. 0 cm) deep. [. . . ] from one outlet during a complete system cycle. A line should be run from this divider valve outlet to the return inlet (F) on the PH Pump. This line allows the lubricant to move the volume indicator plunger (G) to its full "out" position until the undercut (H) on the plunger is exposed. This means that 0. 200 cubic inches of the oil or grease have been delivered to the indicator and that the complete system has cycled. Any excess lubricant will return to the reservoir through the check valve (I). When the volume indicator is pushed in by the lube maintenance person, the lubricant it displaces will also be returned to the reservoir through the check valve. 12415 vent hole in reservoir tube (any remaining air and small amount of grease will exit vent). Loosen system mainline connection at pump outlet. Operate pump until lubricant free of air flows from outlet port. Note, for extreme cases where the pump will not take a prime, it may be helpful to inject several ounces of heavy oil through the grease fill quick disconnect. The pump will then prime on oil pulling the grease behind it. If it becomes necessary to use this method, all injected oil should be discharged at the loosened system supply connection along with any air. Refer to bulletin 12411 (Grease Filler Pump) for manual operated fill pump. SPECIFICATION Pump Body Material Pump Output Max Operating Pressure High Pressure Protection Relief Valve Force to Operate Handle Lubricant Reservoir capacities for Oil or Grease, Metal or Plastic Aluminum and Steel 0. 150 cu. in. (2. 46 cm3) per full stroke 3000 psi (207 bar) Set @ 2500 psi (172 bar) GREASE RESERVOIR FILL PROCEDURE Fill the reservoir with grease, free of air, using a suitable fill pump at the quick disconnect fill plug located in the base of the reservoir. Note, for first time grease filling, or if the grease reservoir has been allowed to go empty, open the petcock in the bottom right side of the reservoir. Slowly begin to fill the reservoir, allowing air trapped under follower to exhaust out the open petcock. When grease free of air flows from the petcock, close petcock and continue to fill the reservoir until follower is at 29 lbs (13. 14 kg) per 1000 psi @ rated pressure Oil or Grease 5 pints (2. 37 liters) or 5 lbs (2. 27 kg) 6 pints (2. 84 liters) or 6 lbs (2. 72 kg) 12 pints (5. 68 liters) or 12 lbs (5. 44 kg) 20 pints (9. 46 liters) or 20 lbs (9. 06 kg) SIDE VIEW END VIEW Page 2 Trabon® PH Manual Pump OPTIONS Two- and Four-Outlet Valves 12415 ORDERING INFORMATION Description PH Pump & 5 pint Plastic Oil Reservoir PH Pump & 5 lb Plastic Grease Reservoir PH Pump & 5 lb Metal Grease Reservoir PH Pump & 6 pint Plastic Oil Reservoir PH Pump & 6 lb Plastic Grease Reservoir PH Pump & 6 lb Metal Grease Reservoir PH Pump & 12 pint Plastic Oil Reservoir PH Pump & 12 lb Plastic Grease Reservoir PH Pump & 12 lb Metal Grease Reservoir PH Pump & 20 pint Plastic Oil Reservoir PH Pump & 20 lb Plastic Grease Reservoir PH Pump & 20 lb Metal Grease Reservoir PH Pump Only Two-Outlet Valve Four-Outlet Valve 3000 psi Pressure Gauge Automatic 2500 psi Relief Valve PH Manual Pump Body Seal Kit Coupler for Grease Fill Stud Part No. 564378 564379 564381 564387 564389 ­ ­ 564383 564384 564385 564386 ­ 563393 564365 ­ 557864 563160 563924 568906 Old Part No. 521-800-100 521-800-130 521-800-160 521-800-370 521-800-400 521-800-430 521-800-190 521-800-220 521-800-250 521-800-280 521-800-310 521-800-340 521-800-000 511-048-001 511-080-000 543-362-000 508-210-250 560-001-930 506-322-000 Two-Outlet Valve -- Four-Outlet Valve -- Two-Outlet Valve -- The two-outlet valve can be used to distribute oil or grease either to two separate manual systems, or to a single manual reversing system (Series Reversing or Bi-Flo). Four-Outlet Valve -- The four-outlet valve can be used to supply lubricant to four separate manual systems or two separate manual reversing systems. With both valves, the inlet port directly above the position of the handle is connected to the outlet port on the bottom of the pump. This handle also indicates the direction of the flow. [. . . ] WHEN FULLY EXTENDED UNDERCUT ON INDICATOR PIN IS EXPOSED. PUSH IN TO RESET 1/4-18 NPSF LUBE OUTLET PORT 3. 000 (76. 2) BOTTOM VIEW All written and visual data contained in this document are based on the latest product information available at the time of publication. Graco reserves the right to make changes at any time without notice. Contact us today! To receive product information or talk with a Graco representative, call 800-533-9655 or visit us online at www. graco. com. ©2006-2009 Graco Inc. All other brand names or marks are used for identification purposes and are trademarks of their respective owners. [. . . ]