User manual GRACO L500CM 3A0133B

[. . . ] Obtain locally. 1 2 Parts labeled n/a are not available as replacement parts. Obtain locally. 1 2 3 Torque to 68-81 N·m (51-59 ft-lb). Torque to 196-210 N·m (145-154 ft-lb). Torque to 68-81 N·m (51-59 ft-lb). Torque to 196-210 N·m (145-154 ft-lb). 3 King Air Motor (not included) King Air Motor (not included) Tie Rods (not included) 2 2 15 16 3 17 11 19 16 15 3 9 8 12 1 9 12 13 1 8 1 13 1 TI14642a TI14644a 2 3A0133B 24C743/24C744 Kit Installation (for Air Motor) 24C743/24C744 Kit Installation (for Air Motor) Be sure to use at least two people when lifting, moving, or connecting the pump. [. . . ] Place the washers (12) and nuts (13) onto the tie rods and torque to 68-81 N·m (51-59 ft-lb). Kit 24C743 (L200CM Pump): Install coupling assembly (15), and slide coupling cover (16) down. Wet Cup 3A0133B 3 Conversion Kit 24D625 Conversion Kit 24D625 To install an L500CM Check-Mate displacement pump on an existing Viscount® II hydraulic motor. 1 8 9 11 12 13 14 15 16 18 Part L500CM n/a 100139 184452 108098 106166 184278 184129 186925 111920 Description Qty. PUMP, displacement; see 312375 1 FITTING, tube 1 PLUG, pipe; 1/8 npt 1 ROD, tie 3 WASHER 3 NUT, tie rod 3 WRENCH; not shown 1 COUPLER 2 NUT, coupling 1 GREASE, lithium 1 Parts labeled n/a are not available as replacement parts. Obtain locally. 1 2 3 Torque to 68-81 N·m (51-59 ft-lb). Torque to 196-210 N·m (145-154 ft-lb). Viscount II Hydraulic Motor (not included) 11 2 15 9 12 1 1 16 8 3 13 TI14950a 4 3A0133B 24D625 Kit Installation (for Hydraulic Motor) 24D625 Kit Installation (for Hydraulic Motor) 7. The wet cup (P) has a covered fill port fitting. A plug (9) is included in this kit and can be installed in place of the covered fitting if desired. The side port of the wet cup is plugged. To install a drain tube, remove the plug and install the supplied 90° tube fitting (8) in its place. (13 mm) ID flexible plastic tube (not supplied) to the fitting to drain any overflow to a pail. Fill wet cup 1/3 full of Graco Throat Seal Liquid or a compatible solvent. Run the pump slowly to ensure that it is operating properly. Allow 2 hours for the adhesive to cure before returning the pump to service. Be sure to use at least two people when lifting, moving, or connecting the pump. If you are connecting the displacement pump to a motor that is still mounted (for example, on a ram), be sure to support the displacement pump while it is being connected, to prevent it from falling and causing injury or property damage. Do this by securely bracing the displacement pump, or by having at least two people hold it while another connects it. 1. Remove the existing displacement pump from the hydraulic motor as explained in your Viscount pump manual. Discard the old coupling nut, couplers, and tie rod nuts. Remove the tie rods from the hydraulic motor and discard. Remove the adapter from the hydraulic motor shaft and discard. Install the new tie rods (11) into the hydraulic motor base. [. . . ] In no event will Graco be liable for indirect, incidental, special or consequential damages resulting from Graco supplying equipment hereunder, or the furnishing, performance, or use of any products or other goods sold hereto, whether due to a breach of contract, breach of warranty, the negligence of Graco, or otherwise. FOR GRACO CANADA CUSTOMERS The Parties acknowledge that they have required that the present document, as well as all documents, notices and legal proceedings entered into, given or instituted pursuant hereto or relating directly or indirectly hereto, be drawn up in English. Les parties reconnaissent avoir convenu que la rédaction du présente document sera en Anglais, ainsi que tous documents, avis et procédures judiciaires exécutés, donnés ou intentés, à la suite de ou en rapport, directement ou indirectement, avec les procédures concernées. Graco Information For the latest information about Graco products, visit www. graco. com. TO PLACE AN ORDER, contact your Graco distributor or call to identify the nearest distributor. [. . . ]