User manual GRACO PRO XS WATERBORNE REV 8-2010

[. . . ] Instructions Manual Electrostatic PROTM Xs Waterborne Air Spray Gun For use with conductive spray materials (waterborne and other materials less than 1 megohm-cm). I hazardous locations using Group D spray materials. 312900D ENG For use in Group II, Zone 1 areas using Group IIA spray materials. II 2 G EEx 0. 24 mJ 247936 Standard Model 247937 Smart Model 100 psi (0. 7 MPa, 7 bar) Maximum Air Inlet Pressure 100 psi (0. 7 MPa, 7 bar) Maximum Working Fluid Pressure Important Safety Instructions: Read all warnings and instructions in this manual. See page 2 for Table of Contents. U. S. Patent Pending Smart Model 247937 Standard Model 247936 Table of Contents Warnings . [. . . ] Test Total Gun Resistance 312900D 23 Electrical Tests Test Power Supply Resistance 1. Remove the turbine alternator (19) from the power supply, page 32. Measure resistance from the power supply's ground strips (EE) to the conductive contact in the center of the power supply seal (FF). If outside this range, replace the power supply. If in range, proceed to the next test. Test Barrel Resistance 1. Insert a conductive rod (GG) into the gun barrel (removed for the power supply test) and against the metal contact (HH) in the front of the barrel. Measure the resistance between the conductive rod (GG) and the charging probe socket (CC). If the resistance is outside the range, replace barrel. If resistance is in range, reassemble the gun and test the gun resistance. If you still have problems, refer to Gun Repair on page 27 for other possible causes of poor performance, or contact your Graco distributor. AA AA FF EE ti1599a Fig. Test Power Supply Resistance GG HH CC ti12821 Fig. Test Barrel Resistance 24 312900D Spray Pattern Troubleshooting Spray Pattern Troubleshooting Electric Shock Hazard Installing and servicing this equipment requires access to parts which may cause an electric shock or other serious injury if the work is not performed properly. Do not install or repair this equipment unless you are trained and qualified. Pressurized Equipment Hazard To reduce the risk of an injury, follow the Pressure Relief procedure on page 19 whenever you are instructed to relieve the pressure. NOTE: Check all possible remedies in the Troubleshooting Chart before disassembling the gun. NOTE: Some spray pattern problems are caused by the improper balance between air and fluid. Problem Cause Solution Fluttering or spitting spray. No fluid. Loose, dirty, damaged nozzle/seat. Refill supply. Clean or replace nozzle, page 28. Air in fluid supply. Damaged nozzle or air cap. Check fluid source. Replace, page 28. Fluid buildup on air cap or nozzle. Fan air pressure too low. See Maintenance on page 20. Dirty or damaged air cap. Reduce viscosity. Clean or replace, page 28. 312900D 25 Gun Operation Troubleshooting Gun Operation Troubleshooting Electric Shock Hazard Installing and servicing this equipment requires access to parts which may cause an electric shock or other serious injury if the work is not performed properly. [. . . ] With the exception of any special, extended, or limited warranty published by Graco, Graco will, for a period of twelve months or two thousand hours of operation from the date of sale, repair or replace any part of the equipment determined by Graco to be defective. However, any deficiency in the barrel, handle, trigger, hook, internal power supply, and alternator (excluding turbine bearings) will be repaired or replaced for thirty-six months or six thousand hours of operation from the date of sale. This warranty applies only when the equipment is installed, operated and maintained in accordance with Graco's written recommendations. This warranty does not cover, and Graco shall not be liable for general wear and tear, or any malfunction, damage or wear caused by faulty installation, misapplication, abrasion, corrosion, inadequate or improper maintenance, negligence, accident, tampering, or substitution of non-Graco component parts. [. . . ]