User manual GRACO PROCONTROL 311190D

[. . . ] Setup, Operation, Service, and Repair TM ProControl 311190D ENG For flow control of mixed, catalyst, and resin coatings. Models with G250, G250HR, or no meters are approved for use in explosive atmospheres. See page 4. Important Safety Instructions Read all warnings and instructions in this manual. Save these instructions. TI6843A Contents Related Manuals . [. . . ] Press Enter to save a value either keyed in from the numerical keypad or selected from a drop-down list. Up Arrow: move to previous field or drop-down list item. Down Arrow: move to next field, or drop-down list item. Alarm Reset Graco PC Cable Port The Graco PC Cable Port is for use with the ProControl Web Interface which enables you to communicate with the ProControl from a PC to: Upgrade software View software version Download · · · job and alarm logs material usage report setup values (can also upload) Clear job, alarm, and material usage reports Upload a custom language to view on screen Restore factory defaults Restore setup password See WEB Interface Software manual 311191 for more information. 311190D 23 EasyKey Display Screens EasyKey Display Screens Power Up Screens When the EasyKey power switch is turned on, the Graco logo screen and current software version screen display for several seconds before the run screen appears in the standby mode. The Run screen displays either the manual run screen or the automatic run screen according to the setup being used at the time the power was shut down. 16. Key 1 Flow Control Tolerance - when flow control is operating. Designates target material flow designated by robot controller. 3 Animation: When there is flow, the gun appears to spray. 4 Status Bar: shows current alarm or operation mode (Run, Standby). 5 Current Date and Time 6 Security Level: a padlock appears on the screen if a password is required to enter Setup mode. If the password was set to "0", no padlock appears and setup can be entered without a password. Designates current material flow designated by robot controller. The only key that functions with the Automatic Run Screen is the Setup key (used to enter Setup . Automatic Run Mode Is used when a varying gun flow is needed such as a robot application where an analog 0 - 10 VDC signal is provided to vary the flow being applied. Automatic Run Mode is selected in the Setup process. See Manual Mode (Automatic or Manual) on page 27. Automatic Run Screen This screen displays the operating status of the system and is the default screen after powering up. 15. 6 3 2 5 mode) and the Alarm Reset Key 1 7 4 FIG. 15 Automatic Run Screen 24 311190D EasyKey Display Screens Manual Run Mode Is used when a constant gun flow is needed such as a reciprocating (back and forth) application and when no analog signal is available for a flow control command. The Manual Run Mode is also used for testing purposes and setup. Manual Run Mode is selected in the Setup process. See Manual Mode (Automatic or Manual) on page 27. 3 Status Bar: shows operation mode or current alarm (Run, Standby). 4 Current Date and Time 5 Security Level: a padlock appears on the screen if a password is required to enter Setup mode. If the password was set to "0", no padlock appears and setup can be entered without a password. 5 4 2A Flow Control Tolerance Appears in both the Automatic Run Mode Screen and the Manual Run Mode Screen. This indicator band visually shows how well a +/- flow rate tolerance is being held during product application, see FIG. Set the flow rate tolerance of the color from 1­50% in increments of 1%. [. . . ] With the exception of any special, extended, or limited warranty published by Graco, Graco will, for a period of twelve months from the date of sale, repair or replace any part of the equipment determined by Graco to be defective. This warranty applies only when the equipment is installed, operated and maintained in accordance with Graco's written recommendations. This warranty does not cover, and Graco shall not be liable for general wear and tear, or any malfunction, damage or wear caused by faulty installation, misapplication, abrasion, corrosion, inadequate or improper maintenance, negligence, accident, tampering, or substitution of non-Graco component parts. Nor shall Graco be liable for malfunction, damage or wear caused by the incompatibility of Graco equipment with structures, accessories, equipment or materials not supplied by Graco, or the improper design, manufacture, installation, operation or maintenance of structures, accessories, equipment or materials not supplied by Graco. [. . . ]