User manual GRACO RTX 650

[. . . ] Operation Interior Texture Sprayer RTX 650 311767B For Water-Based Materials Only Model 254973: 50 psi (3. 5 bar) Maximum Fluid Working Pressure 100 psi (7 bar) Maximum Air Input Pressure Important Safety Instructions Read all warnings and instructions in this manual. Save these instructions. Related Manuals 311777 311771 ti8370a Model 254973 Shown Graco Inc. Box 1441 Minneapolis, MN 55440-1441 Copyright 2006, Graco Inc. EN ISO 9001 US C Conforms to ANSI/UL standard 1450 Warnings Warnings The following are general warnings related to the setup, use, grounding, maintenance and repair of this equipment. [. . . ] Point gun into waste bucket and pull trigger to pump water through the system. Continue to trigger gun until material hopper is empty. To achieve uniform spray pattern, adjust air valve and flow adjustment nut on gun. If you can not achieve a desired pattern, change nozzle, page 10. ti8376a 10. Add pre-mixed texture mix to material hopper. See Mixing Material, page 9. Fluid flow will be restricted if the material hose is kinked. 8 Mixing Material Mixing Material Correct material mixture is essential. The pump will not operate if the mixture is too thick. Mix the material in a separate container before pouring it into hopper. Use Material Thickness Gauge to determine mixture is thin enough to spray. *The Material Thickness Gauge will only determine if the material is thin enough to pass through the pump. For some applications or for higher speed spraying, your mixture may need to be thinner. For best results do not use partial bags of material. (18 kg) bag of texture material to 5-6 gallons (18. 9-22. 7 liters) of clean water as instructed on the bag instructions. After texture material is thoroughly mixed, gently set ball end of Material Thickness Gauge on surface of mixture. For an accurate test, be sure gauge is completely dry and clean every time it is used. When the material is thin enough to spray the ball will sink completely into the mixture. READY ADD WATER ti2498a 6. If the ball does not sink completely into the mixture within 10 seconds, add more water, agitate and try test again. Slowly add approximately 2 to 4 qts (1. 9 to 3. 8 liters) of water to a 5 gallon (18. 9 liter) bucket of premix. READY ADD WATER ti2496 ti2498a 2. Agitate to mix, using a half-inch, variable speed drill with mixing paddle, to a smooth, lump-free consistency. 2. Agitate to mix, using a half-inch, variable speed drill with a mixing paddle, to a smooth, lump-free consistency. After texture material is thoroughly mixed, gently set ball end of Material Thickness Gauge on surface of mixture. For an accurate test, be sure gauge is completely dry and clean every time it is used. ti2497#1 3. [. . . ] Sound Data (less compressor) Sound Pressure Level . 120 Vac, 60 Hz, 15A, 1 phase 50 psi, (3. 5 bar) 100 psi (7. 0 bar) Universal motor thermally protected, oil-less 3. 5 @ 40 psi minimum 3500 W minimum Permanent Magnet DC-5A 16 AWG, 3-wire, 15 ft 5 gallons 0. 65 gpm 19 in. (508 mm) 33 lb (14. 9 kg) brass, aluminum, plastic N/A N/A 35°F - 160°F (1. 6°C - 71°C) 40°F - 115°F (4°C - 46°C) 70 psi (3. 5 bar) 125 psi (8. 75 bar) 3. 0 - 11 CFM 1. 1 lb (500 g) 14 Notes Notes 15 Graco Warranty Graco Warranty Graco warrants all equipment referenced in this document which is manufactured by Graco and bearing its name to be free from defects in material and workmanship on the date of sale to the original purchaser for use. With the exception of any special, extended, or limited warranty published by Graco, Graco will, for a period of twelve months from the date of sale, repair or replace any part of the equipment determined by Graco to be defective. [. . . ]