User manual GRACO TURBINE ALTERNATOR 308034

[. . . ] D Electrostatic equipment must be used only by trained, qualified personnel who understand the requirements stated in this instruction manual and in the spray gun instruction manual. D Read all the instruction manuals, tags, and labels before operating the equipment. EQUIPMENT MISUSE HAZARD Equipment misuse can cause the equipment to rupture, malfunction, or start unexpectedly and result in a serious injury. D Do not alter or modify this equipment. Use only genuine Graco parts and accessories. [. . . ] Using a drift punch or small metal shaft, tap the armature (D) out of the bearing (1) and fan (3). WARNING To reduce the risk of serious injury whenever you are instructed to relieve pressure, always follow the Pressure Relief Procedure in your spray gun manual or in the SuperCat instruction manual. Disassembly 1. See your spray gun manual to remove the power cartridge. For the SuperCat alternator, remove six screws, open the housing, and remove the power cartridge. Test the Coil: Measure the resistance between the two outer terminals of the 3-pin connector (101a). Measure the resistance between each outer terminal of the 3-pin connector and the turbine alternator housing (B). If the readings vary from these values, replace the coil. Remove the plastic plug (A). CAUTION To avoid demagnetization of the armature (D), never place it in contact with, or in close proximity to, any other armature or other ferromagnetic objects. Clean the armature (D) shaft with a soft cloth. 217590) if necessary. 2 308034 Turbine Alternator Service KEY A B D E G H 1 2 3 101 101a Plug Turbine Alternator Housing Armature O-Ring Turbine Assembly Retaining Ring (Pro Xs only) Bearing Bearing Fan Coil 3-Wire Connector PRO 3500 / 4500 / 5500, PRO Pulse, and SuperCat, Xtreme Mix 185, ProMix Easy, and ProMix I Proportioners E A B Exhaust Port G D 101 2 101a 1 3 E A B PRO Xs Models H PRO Xs only NOTE: The items referenced with numbers are included with a kit. TI15230a Fig. Remove the bearings (1 & 2) from the package and wipe the excess oil off with a soft cloth. Do not use solvent or air to wipe or blow off the excess oil. Place the smaller bearing (1) [marked 197906] on the long end of the armature (D), with the machined groove in the bearing facing the armature. Install the fan (3) on the long end of the armature (D), with the machined groove in the fan facing away from the armature. Insert the spacing tool (4) between the fan (3) and bearing (1). Lightly tap on the end of the armature (D) until the fan is pressed up against the spacing tool and bearing. When properly installed, the bearing (1) should spin freely on the armature shaft. Install the coil assembly (101) over the armature (D), with the 3-wire connector (101a) facing away from the fan (3). 6. Place the larger bearing (2) [marked 197907] on the end of the armature (D), with the machined groove in the bearing (2) facing in toward the armature. Align the legs of both bearings with each other. NOTE: When installed, the bearing legs must not block the exhaust ports of the turbine alternator housing (B) or the gun will not operate properly. [. . . ] 244577 Description COIL 101 Qty 1 4 TI1884A Graco Information For the latest information about Graco products, visit www. graco. com. TO PLACE AN ORDER, contact your Graco distributor or call to identify the distributor closest to you: Phone: 612­623­6921 or Toll Free: 1­800­328­0211 Fax: 612­378­3505 All written and visual data contained in this document reflects the latest product information available at the time of publication. Graco reserves the right to make changes at any time without notice. MM 308034 Graco Headquarters: Minneapolis International Offices: Belgium, China, Japan, Korea GRACO INC. [. . . ]