User manual GRASS VALLEY 8949MDA-SXF DATASHEET

[. . . ] 40 8949MDA-SXF SDI Monitoring Distribution Amplifier Key Features · Reclocked distribution of SD or HD-SDI signals for reconstructed input fan-out · SD-SDI monitoring · Can distribute both HD-SDI and SD-SDI with automatic format detection for flexible future-proof system architectures · Provides SD monitoring output whether input is SD or HD · Very high-density solution · Accepts optional fiber transmitter to provide optical, HD-SDI, and SD-SDI monitoring outputs for combined local/ remote systems · Configurable as fiber receiver with four HD-SDI outputs and SD-SDI monitoring · High-quality downscaled signals with new EDH CRC packet generated on outputs The 8949MDA-SXF is a monitoring distribution amplifier with SD-SDI monitoring outputs. [. . . ] Applications include use as an HD-SDI fiber transmitter with additional monitoring and reclocked coax feeds. Or the module can have a dual receiver (two fiber inputs) or a transceiver (one fiber input and one fiber output). All parameters can be adjusted directly from the module itself or via standard HTML Web browsers or via the Newton Control Panel (when installed in network-equipped frames). In addition NetConfig and NetCentral can be used for remote configuration and signal health monitoring. This is a monitoring device so, in order to provide the fastest possible conversion, the module does not perform de-interlacing and consequently it has an extremely short processing delay of 0. 95 ms. SD/HD SDI In 8900WFR-XFR SD/HD SDI Out SD/HD SDI Out SD/HD SDI Out SD/HD SDI Out SD/HD SDI In J1 J2 SD SDI Out SD SDI Out SD SDI Out SD SDI Out Fiber I/O Connector J3 J4 J5 J6 J7 J8 J9 FIBER Applications · Where an SD-SDI monitoring feed is required · HD-SDI distribution alongside SD-SDI monitoring · Rate-agile systems requiring consistent SD feed monitoring · A fiber receiver with SD monitoring · A fiber transmitter with local SD and HD monitoring feeds Equalizer and Re-clocker Aspect Ratio Control Downconverter 4X SD/HD-SDI Out Only one fiber option may be selected Fiber RX Option Fiber RX SD/HD Optical In Fiber RX Option Auto Format Detection 4X SD-SDI Out Fiber TX Option Fiber TX Fiber TX SD/HD Optical Out Specifications Supported Frame Types GeckoFlex frame Ordering Information Electrical Length (Delay) <0. 95 ms This module can be mounted in a GeckoFlex frame but not in other 8900 series frames including Gecko-A or Gecko-V frames. Power Rating 8. 1 Watts ­ single slot without fiber optic submodule 8. 8 Watts ­ single slot with fiber optic submodule Conversion 10 bits representation Type: Field-based high-speed monitoring to drive 16:9 monitors Input formats 59. 94 Hz: 1080i @ 59. 94 Hz, 720p @ 59. 94 Hz, 480i @ 59. 94 Hz ·Tooutputformat:480i@59. 94Hz Input formats 50 Hz: 1080i @ 50 Hz, 720p @ 50 Hz, 576i @ 50 Hz ·Tooutputformat:576i@50Hz Manual input selection: Coax In, fiber 1, fiber 2 (with optional fiber input) Input format selection: Automatic/manual 8949MDA-SXF SD/HD monitoring distribution amplifier SDI output ­ fiber ready front and rear module set. Fiber optic kit option includes one fiber optic submodule, mounting bracket, and fiber cable assembly for mounting on the module circuit board. Inputs SD/HD-SDI: ·Inputequalization:upto125mHD-SDI, up to 330m SD-SDI (Belden1694A) ·Returnloss:>15dB0. 004to1. 5GHz Optical: Single-mode (optional) Formats supported: 1080i @ 59. 94, 50, 720p @ 59. 94, 50, 480i @ 59. 94 (NTSC) 576i @ 50 (PAL-B) SFP-13103G-M1DRX-K Dual input fiber receiver kit. For one-signal-per-fiber and CWDM fiber systems SFP-13103G-M1DTX-K Dual output fiber transmitter kit. For one-signal-perfiber systems Outputs SD/HD-SDI: Four outputs ·Returnloss:>15dB, 5to270MHz; >10 dB to 1. 5 GHz ·Signallevel:SDI800mVp-p±10% ·Outputjitter:forinputwith<0. 1UIjitter, theoutput jitter complies with the SMPTE 259M & 292M standards SD-SDI: Four outputs ·Returnloss:>15dB, 5to270MHz ·Signallevel:SDI800mVp-p±10% ·Outputjitter:forinputwith<0. 1UIjitter, theoutput jitter complies with the SMPTE 292M standards Control and Monitoring SNMP: Yes Web page configuration: Yes Local configuration: Yes Newton support: Yes NetConfig support: Yes NetCentral support: Yes SFP-13103G-M1TRX-K Fiber transceiver kit. [. . . ] To provide the fastest possible conversion, this module does not perform de-interlacing and consequently it has an extremely short For detailed specifications, installation, and setup instructions see: www. grassvalley. com/docs/modular [. . . ]